Changing or Replacing UNIGATE® CO(M)-ProfibusDP by UNIGATE® CM-PB

Aus Deutschmann Wiki
Zur Navigation springen Zur Suche springen

The table below describes which points need to be observed when changing or replacing UNIGATE® CO(M) - ProfibusDP by UNIGATE® CM-PB.

UNIGATE® CO(M) - ProfibusDP UNIGATE® CM-PB Note
UNIGATE CO(M) - ProfibusDP.png
UNIGATE CM-PB.jpg
UNIGATE® CM-PB: UNIGATE® CM-PB ist available in housing colour Blue. Attention: OEM-devices may vary in colour.
Protocol Green check.svg Green check.svg (*see note) UNIGATE® CM-PB: Universalscript Deutschmann CM is loaded by factory setting. This contains beside the CANopen mapping, which is also available in UNIGATE® CO(M) - ProfibusDP also further protocols. By configuration software WINGATE can be selected the needed protocol and UNIGATE® CM-PB maybe configured and used as UNIGATE® CO(M) - ProfibusDP.
Script Red x.svg Green check.svg
Software
configuration software WINGATE Green check.svg Green check.svg UNIGATE® CM-PB: The configuration file (*.gwc) of UNIGATE® CO(M) - ProfibusDP can not be loaded in UNIGATE® CM-PB.
Mechanics
Housing WxHxD 90 x 127 x 55 mm 23 x 117 x 117 mm
Protection type IP24 IP20
Connection-Power Supply Mounting Position
Frontal-Bottom Bottom
Schraub-Steckverbinder 2 pol.
Schraub-Steckverbinder X2
Power Supply Screw-Plug-Connector 2 pol. (for 9 pol. D-Sub Plug-Connector) Screw-Plug-Connector 4 pol. X2
+24V/DC Pin 1 Pin 1
0V (GND) Pin 2 Pin 2
Housing-Earthing Earthing Clamp via DIN-Rail Earthing Clamp via DIN-Rail
UNIGATE CO(M) - ProfibusDP (Gehäuse-Erde)
UNIGATE CM-PB (Gehäuse-Erde)
UNIGATE® CO(M) - ProfibusDP: At elder devices the earthing is done by flat plug connectors or there is no earthing at the device.
Beispiel zeigt UNIGATE CO(M) - ProfibusDP mit Erdung über Flachsteckeranschlüsse
Connection Serial Mounting Position
Side Part - right Top Bottom
Für 3 pol. Schraub-Steckverbinder
Schraub-Steckverbinder X1
Schraub-Steckverbinder X2
Application Interface (RS232) Screw-Plug Connector 3 pol. Screw-Plug-Connector 3 pol. X1 Red x.svg
Rx Pin 1 Pin 1 Red x.svg
Tx Pin 2 Pin 2 Red x.svg
AP-GND Pin 3 Pin 3 Red x.svg
Application Interface (RS485) Red x.svg Screw-Plug-Connector 4 pol. X1 Red x.svg
RS485 (+) Red x.svg connect Pin 4 with Pin 6 Red x.svg
RS485 (-) Red x.svg connect Pin 5 with Pin 7 Red x.svg
Application Interface (RS422) Red x.svg Screw-Plug-Connector 4 pol. X1 Red x.svg
Rx422 (+) Red x.svg Pin 4 Red x.svg
Rx422 (-) Red x.svg Pin 5 Red x.svg
Tx422 (+) Red x.svg Pin 6 Red x.svg
Tx422 (-) Red x.svg Pin 7 Red x.svg
Debug-Interface Red x.svg Red x.svg Screw-Plug-Connector 4 pol. X2
Rx-Debug Red x.svg Red x.svg Pin 3
Tx-Debug Red x.svg Red x.svg Pin 4
Selection Application Interface Not selectable Not selectable/configurable
RS232 Green check.svg Green check.svg(*see note) UNIGATE® CM-PB: In connection with Universalscript Deutschmann CM is only Application Interface RS232 available.
RS485 Red x.svg Green check.svg (*see note)
RS422 Red x.svg Green check.svg (*see note)
Termination
RS422 (Tx) Red x.svg Connectible by slide switch below X1 UNIGATE® CM-PB: Below X1 are to be found 2 slide switches for termination.
Schiebeschalter Abschlusswiderstand Applikations- Schnittstelle
RS422 (Rx) Red x.svg Connectible by slide switch below X1
RS485 Red x.svg Connectible by one slide switch below X1 UNIGATE® CM-PB: Only slide switch Tx422 has to be set to position ON. Slide switch Rx422 has to be set to position OFF.
Application- Interface Rotary Coding Switches & LEDs Mounting Position Application- Interface Rotary Coding Switches & LEDs
Frontal-Unten Frontal
Applikations- Schnittstelle LEDs
Applikations- Schnittstelle Drehkodierschalter & LEDs
Rotary Coding Switch S4 Red x.svg Green check.svg Rotary Coding Switch S4 UNIGATE® CM-PB: Operating modes may be selected correspondingly as at UNIGATE® CO(M) - ProfibusDP, . Attention: Switch position "DD" is reserved for internal use and is not allowed to use.
Rotary Coding Switch S5 Red x.svg Green check.svg Rotary Coding Switch S5
LED Power Red x.svg Green check.svg LED Power
LED State Red x.svg Green check.svg LED State
LED Error No / Select ID Green check.svg Green check.svg LEDs 1/2/4/8 (Error No / Select ID)
Connection Fieldbus Mounting Position
Frontal-Top Frontal-Bottom Frontal Top
CANopen Red x.svg
Anschluss über 9 pol. D-Sub Stecker
Red x.svg
Anschluss über 4 pol. Stecker
PROFIBUS
Anschluss über 9 pol. D-Sub-Buchse
Red x.svg
Anschluss über 9 pol. D-Sub-Buchse
Red x.svg
Termination Connectible by slide switch Connectible by slide switch
Fieldbus Rotary Coding Switches & LEDs Einbaulage Fieldbus Rotary Coding Switches/Dip-switch/LEDs
Frontal-Top Frontal Bottom Frontal Top
CANopen Red x.svg
Feldbus Dipschalter & LEDs
Feldbus LED
Red x.svg CANopen
Dip-Switch Red x.svg Green check.svg Red x.svg Red x.svg Dip-Switch
LED BUS Power Red x.svg Green check.svg Green check.svg Red x.svg LED Power/State
LED BUS State Red x.svg Green check.svg Red x.svg
PROFIBUS
Feldbus Drehkodierschalter & LEDs
Red x.svg
Feldbus Drehkodierschalter & LEDs
Red x.svg PROFIBUS
Rotary Coding Switch High Green check.svg Red x.svg Green check.svg Red x.svg Rotary Coding Switch High
Rotary Coding Switch LOW Green check.svg Red x.svg Green check.svg Red x.svg Rotary Coding Switch LOW
LED BUS Power Green check.svg Red x.svg Green check.svg Red x.svg LED BUS Power
LED BUS Error Green check.svg Red x.svg Green check.svg Red x.svg LED BUS
LED BUS State Green check.svg Red x.svg Green check.svg Red x.svg LED BUS State
Device Description Files
CANopen Red x.svg Green check.svg UNIGATE® CM-PB: An EDS - file can be generated by configuration software WINGATE.
PROFIBUS DPV0 DAGW2862.gsd DAGW2862.gsd UNIGATE® CM-PB: The Ident Number may be set to "2862" via configuraton software WINGATE. With this setting the old GSD-file can be kept and the project needs not to be changed.
PROFIBUS DPV1 Red x.svg UGIC3218.gsd

Green check.svg = available
Red x.svg = not available
Weitere, detaillierte Informationen, befinden sich im jeweiligen Handbuch unter Kapitel "Technische Daten".