Changing or Replacing UNIGATE® CO(M)-ProfibusDP by UNIGATE® CX-C4Map-PBDPV1

The table below describes which points need to be observed when changing or replacing UNIGATE® CO(M)-ProfibusDP by UNIGATE® CX-C4Map-PBDPV1. In addition to the information on the hardware and software, this also contains information on the EPLAN files so that the documentation can be adapted accordingly if necessary.

	UNIGATE® CO(M)-ProfibusDP		UNIGATE® CX		Note
					UNIGATE® CX: UNIGATE® CX is only available in housing colour Grey.
Protocol			(*see note)		UNIGATE® CX-C4Map: UNIGATE® CX-C4Map-PBDPV1 contains the CANopen Mapping. Via the configuration software WINGATE, the CANopen Mapping can be done. UNIGATE® CX-C4Map-PBDPV1 can thus be used like the UNIGATE® CO(M)-ProfibusDP.
Software
Konfigurationssoftware WINGATE					UNIGATE® CX: The configuration file (*.gwc) of UNIGATE® CO(M) - ProfibusDP can not be loaded inUNIGATE® CX-C4Map-PBDPV1.
Mechanics
Housing WxHxD	90 x 127 x 55 mm		46 x 117 x 106 mm
Protection type	IP24		IP20
Connection-Power Supply	Mounting Position
	Frontal-Bottom		Bottom
	screw-plug-connector 2 pol.		screw-plug-connectorr X1 and X2
Power Supply	screw-plug-connector 2 pol.		screw-plug-connector 4 pol. X1	screw-plug-connector 4 pol. X2
+24V/DC (Pwr)	Pin 1		Pin 1		UNIGATE® CX: The power supply is internally bridged between + 24V/DC (Pwr) and + 24V/DC (Out) as well as between 0V (GND) (Pwr) and 0V (GND) (Out). This only has to be done at + 24V/DC (Pwr) and 0V (GND) (Pwr).
0V (GND) (Pwr)	Pin 2		Pin 2
+24V/DC (Out)				Pin 1
0V (GND) (Out)				Pin 2
Housing-Earthing	Earthing Clamp via DIN-Rail		Earthing Clamp via DIN-Rail
	UNIGATE CO(M) - ProfibusDP (Housing-Earthing)		UNIGATE CX (Housing-Earthing)		UNIGATE® CO(M) - ProfibusDP: At elder devices the earthing is done by flat plug connectors or there is no earthing at the device. Example shows UNIGATE CO(M) - ProfibusDP
Anschluss-Seriell	Mounting Position
	Side Part - right		Top	Bottom
	For 3 pol. screw-plug-connector		screw-plug-connector Service Interfaces	screw-plug-connector X1 und X2
Application Interface (RS232)	screw-plug-connector 3 pol.		screw-plug-connector 3 pol. Service Interfaces
Rx	Pin 1		Pin 1
Tx	Pin 2		Pin 2
AP-GND	Pin 3		Pin 3
Debug-Interface				screw-plug-connector 4 pol. X1 screw-plug-connector 4 pol. X2
Rx-Debug				Pin 3
Tx-Debug				Pin 4
Selection Application Interface	Not selectable		Configurable
RS232			(*see note)		UNIGATE® CX: The RS232 interface is used exclusively as a service interface. For example, a 'Reset device' or a 'Firmware Update' (* .hex) can be carried out via this.
Application- Interface Rotary Coding Switches & LEDs	Mounting Position
	Frontal		Frontal
	application interface LEDs		application interface rotary coding switches & LEDs
Rotary Coding Switch S4					UNIGATE® CX: Operating modes may be selected correspondingly as at UNIGATE® CO(M) - ProfibusDP. Attention: Switch position "DD" is reserved for internal use and is not allowed to use.
Rotary Coding Switch S5
LED Power
LED State
LEDs 1/2/4/8 (Error No / Select ID)
Connection Fieldbus	Mounting Position
	Frontal-Top	Frontal-Bottom	Frontal	Top
CANopen		connection via 9 pol. D-Sub connector	connection via 9 pol. D-Sub connector
PROFIBUS	connection via 9 pol. D-Sub socket		connection via 9 pol. D-Sub socket
Termination	Connectible by slide switch		Connectible by slide switch
Fieldbus Rotary Coding Switches & LEDs	Mounting Position
	Frontal-Top	Frontal Bottom	Frontal
CANopen		fieldbus Dip-Switch & LEDs	CANopen Dip-Switch & LEDs
Dip-Switch
LED BUS Power
LED BUS State
PROFIBUS	fieldbus rotary-coding-switches & LEDs		PROFIBUS rotary-coding-switches & LEDs
Rotary Coding Switch High
Rotary Coding Switch LOW
LED BUS Power
LED BUS Error
LED BUS State
Device Description Files
CANopen					UNIGATE® CX: An EDS - file can be generated by configuration software WINGATE.
PROFIBUS DPV0	DAGW2862.gsd		UGIC3218.gsd		UNIGATE® CX: The GSD file for the PROFIBUS can be downloaded from the homepage. GSD-Datei (GSD-File) Icon (DIB-File)
PROFIBUS DPV1			UGIC3218.gsd		UNIGATE® CX: The GSD file for the PROFIBUS can be downloaded from the homepage. GSD-Datei (GSD-File) Icon (DIB-File)
EPLAN
CANopen					UNIGATE® CX: The macro for EPLAN can be downloaded from the homepage. EPLAN - Makro Unigate CL-C4 (Zip-Datei) Compatibility list macros UNIGATE® CL/CX (PDF-File)
PROFIBUS					UNIGATE® CX: The macro for EPLAN can be downloaded from the homepage. EPLAN - Makro Unigate CL-PB (Zip-Datei) Compatibility list macros UNIGATE® CL/CX (PDF-File)

= available
= not available
Further detailed information may be found in the corresponding manual in chapter "Technical Data".