Device Replacement LOCON 24/48/64: Unterschied zwischen den Versionen

Aus Deutschmann Wiki
Zur Navigation springen Zur Suche springen
Zeile 1: Zeile 1:
Depending on the version, LOCON 24, LOCON 48 and LOCON 64 as well as the corresponding PM-Versions may be replaced by a corresponding [[LOCON 24 (English)|LOCON 24]] (-PM) oder [[LOCON 48 (English)|LOCON 48]] (-PM) or [[LOCON 100 (English)|LOCON 100]] and an extension module [[LOCON 100 (English)#Erweiterungsmodul|LOCON 100-Out I/O32]]  or [[LOCON 200 (English)|LOCON 200]] with a corresponding number of extension modules [[LOCON 200 (English)#Erweiterungsmodul|LOCON 200-Out I/O8]]. ('''Attention:''' For a configuration level step of more then '''8 pieces''' LOCON 200-Out I/O8 is needed in addition a [[LOCON 200 (English)#NT-Modul|NT-Module]].  
+
Depending on the version, LOCON 24, LOCON 48 and LOCON 64 as well as the corresponding PM-Versions may be replaced by a corresponding [[LOCON 24 (English)|LOCON 24]] (-PM) oder [[LOCON 48 (English)|LOCON 48]] (-PM) or [[LOCON 100 (English)|LOCON 100]] and an extension module [[LOCON 100 (English)#Erweiterungsmodul|LOCON 100-Out I/O32]]  or [[LOCON 200 (English)|LOCON 200]] with a corresponding number of extension modules [[LOCON 200 (English)#Erweiterungsmodul|LOCON 200-Out I/O8]]. ('''Attention:''' For a configuration level step of more then '''8 pieces''' LOCON 200-Out I/O8 is needed in addition a [[LOCON 200 (English)#NT-Modul|NT-Module]]).  
 
In order to ensure a proper and fast replacement, we would need the following information and components:
 
In order to ensure a proper and fast replacement, we would need the following information and components:
 
#The serial-no. or the article-no.(Vxxxx) of the old device has to be known in order to offer a corresponding new device. If the replacement would be done with a new cam control '''without''' control panel (LOCON 24-PM, LOCON 48-PM, LOCON 100 und LOCON 200) then for operation would be the need of [[TERM 6 (English)|TERM 6]] or [[TERM 24 (English)|TERM 24]] or [[WINLOC 32 (English)|WINLOC 32]]-Basic- or comfort version.
 
#The serial-no. or the article-no.(Vxxxx) of the old device has to be known in order to offer a corresponding new device. If the replacement would be done with a new cam control '''without''' control panel (LOCON 24-PM, LOCON 48-PM, LOCON 100 und LOCON 200) then for operation would be the need of [[TERM 6 (English)|TERM 6]] or [[TERM 24 (English)|TERM 24]] or [[WINLOC 32 (English)|WINLOC 32]]-Basic- or comfort version.

Version vom 28. April 2017, 09:52 Uhr

Depending on the version, LOCON 24, LOCON 48 and LOCON 64 as well as the corresponding PM-Versions may be replaced by a corresponding LOCON 24 (-PM) oder LOCON 48 (-PM) or LOCON 100 and an extension module LOCON 100-Out I/O32 or LOCON 200 with a corresponding number of extension modules LOCON 200-Out I/O8. (Attention: For a configuration level step of more then 8 pieces LOCON 200-Out I/O8 is needed in addition a NT-Module). In order to ensure a proper and fast replacement, we would need the following information and components:

  1. The serial-no. or the article-no.(Vxxxx) of the old device has to be known in order to offer a corresponding new device. If the replacement would be done with a new cam control without control panel (LOCON 24-PM, LOCON 48-PM, LOCON 100 und LOCON 200) then for operation would be the need of TERM 6 or TERM 24 or WINLOC 32-Basic- or comfort version.
  2. If TERM 6 or TERM 24 is already used, then we have to know the serial-no. of this devices, too, in order to check the compatibilty to the new device.
  3. For read-out of the old device and, if needed, the configuration and programming of a new device with WINLOC32-Basic-or-comfort Version would be needed a corresponding programming cable. Note: It has to be checked in every single case if this programming cable may be used also for a needed read out of the old device.
  4. For the configuration of a new device, if needed, you have to use TERM 6 or die WINLOC 32-Basic-or comfort version.
  5. For the configuration and programming with WINLOC 32-Basic-or-comfort Version, the PC is in need of a real COM-Port. If there exists no more real COM-Port at the PC, then a USB-to-RS232 converter has to be used.

For a corresponding offer please let us know the serial-no. or the article-no. (Vxxxx) of the old device and, if used, the serial-no. of TERM 6 resp. TERM 24.