Device replacement LOCON 32: Unterschied zwischen den Versionen

Aus Deutschmann Wiki
Zur Navigation springen Zur Suche springen
Zeile 1: Zeile 1:
 
The device types LOCON 32-HC, LOCON 32-HC-4X, LOCON 32PM and LOCON 32PM-4X can be replaced by a corresponding number of [[LOCON 200 (English)|LOCON 200]] and a corresponding number of [[LOCON 200 (English)#Erweiterungsmodul|LOCON 200-Out I/O8]] or a corresponding number of [[LOCON 24 (English)|LOCON 24]].   
 
The device types LOCON 32-HC, LOCON 32-HC-4X, LOCON 32PM and LOCON 32PM-4X can be replaced by a corresponding number of [[LOCON 200 (English)|LOCON 200]] and a corresponding number of [[LOCON 200 (English)#Erweiterungsmodul|LOCON 200-Out I/O8]] or a corresponding number of [[LOCON 24 (English)|LOCON 24]].   
 
In order to ensure a proper and fast replacement and programming of the new devices, we would need the following information and components:
 
In order to ensure a proper and fast replacement and programming of the new devices, we would need the following information and components:
#The serial-no. or the article-no.(Vxxxx) of the old device has to be known in order to offer a corresponding new device.If a new cam control '''without''' control panel (LOCON 200 und LOCON 24-PM) will be used, then for operation is needed a [[TERM 6 (English)|TERM 6]] or [[TERM 24 (English)|TERM 24]] or [[WINLOC 32 (English)|WINLOC 32]]-Basic-or Comfortversion. '''Hinweis:''' Bei Geräteaustausch durch LOCON 24 muss außerdem bekannt sein, welcher Geber und welche Totzeit verwendet wird, da diese nicht frei konfigurierbar sind.
+
#The serial-no. or the article-no.(Vxxxx) of the old device has to be known in order to offer a corresponding new device.If a new cam control '''without''' control panel (LOCON 200 und LOCON 24-PM) will be used, then for operation is needed a [[TERM 6 (English)|TERM 6]] or [[TERM 24 (English)|TERM 24]] or [[WINLOC 32 (English)|WINLOC 32]]-Basic-or Comfortversion. '''Note:''' If the unit is replaced by LOCON 24 it has to be known which Encoder abd which idletime is used, as these are not freely configurable.
  
 
#For read-out of the old device and, if needed, the programming and configuration of a new device with WINLOC32-Basic-or-comfort Version would be needed a corresponding programming cable. '''Note:''' It has to be checked in every single case if this programming cable may be used also for a needed read out of the old device.  
 
#For read-out of the old device and, if needed, the programming and configuration of a new device with WINLOC32-Basic-or-comfort Version would be needed a corresponding programming cable. '''Note:''' It has to be checked in every single case if this programming cable may be used also for a needed read out of the old device.  

Version vom 13. Januar 2017, 11:11 Uhr

The device types LOCON 32-HC, LOCON 32-HC-4X, LOCON 32PM and LOCON 32PM-4X can be replaced by a corresponding number of LOCON 200 and a corresponding number of LOCON 200-Out I/O8 or a corresponding number of LOCON 24. In order to ensure a proper and fast replacement and programming of the new devices, we would need the following information and components:

  1. The serial-no. or the article-no.(Vxxxx) of the old device has to be known in order to offer a corresponding new device.If a new cam control without control panel (LOCON 200 und LOCON 24-PM) will be used, then for operation is needed a TERM 6 or TERM 24 or WINLOC 32-Basic-or Comfortversion. Note: If the unit is replaced by LOCON 24 it has to be known which Encoder abd which idletime is used, as these are not freely configurable.
  1. For read-out of the old device and, if needed, the programming and configuration of a new device with WINLOC32-Basic-or-comfort Version would be needed a corresponding programming cable. Note: It has to be checked in every single case if this programming cable may be used also for a needed read out of the old device.
  2. For a configuration of the new device, if needed, you have to use a TERM 6 or WINLOC 32-Basic-or Comfortversion.
  3. For the configuration and programming of the new device with WINLOC 32-Basic-or-comfort Version, the PC is in need of a real COM-Port. If there exists no more real COM-Port at the PC, then a USB-to-RS232 converter has to be used.

For a corresponding offer please let us know the serial-no. or the articel-no. (Vxxxx) of the old device.