Device replacement ROTARNOCK - PROFIBUS (English): Unterschied zwischen den Versionen

Aus Deutschmann Wiki
Zur Navigation springen Zur Suche springen
 
(15 dazwischenliegende Versionen von 2 Benutzern werden nicht angezeigt)
Zeile 1: Zeile 1:
'''ROTARNOCK 1-PB''' und '''ROTARNOCK 2-PB''' can be replaced by '''ROTARNOCK 100-PB''' . As an 1:1 exchange is not possible, the following points have to be noted:
+
'''ROTARNOCK 1-PB''', '''ROTARNOCK 2-PB''' and '''ROTARNOCK 80-PB''' can be replaced by '''ROTARNOCK 100-PB''' . As an 1:1 exchange is not possible, the following points have to be noted:
  
 
==Device Configuration==  
 
==Device Configuration==  
The configuration has to be done with our software [[WINLOC 32]]-Basis-oder Komfortversion durchgeführt werden. Daür wird ein entsprechendes [[Programmierkabel]] benötigt. '''Hinweis:''' Ob dieses Programmierkabel auch für ein ggf. benötigtes Auslesen des Altgerätes verwendet werden kann, muss im jeweiligen Fall geprüft werden. '''Achtung:''' Für die Konfiguration muss ein echter COM-Port am PC vorhanden sein. Wenn kein echter COM-Port mehr am PC vorhanden ist, wird ein [[USB-RS232-Konverter]] benötigt.
+
The configuration has to be done with our software [[WINLOC 32 (English)|WINLOC 32]]-Basis-or Comfort version. Herefore is needed a corresponding [[Programming cable]]. '''Note:''' Whether the programming cable can also be used for a necessary read-out of the old device has to be tested in each case! '''Attention:''' For the configuration, the PC is in need of a real COM-Port. If there is no real COM-Port at the PC, then an [[USB-to-RS232 converter]] has to be used.
*'''Virtuelle Geberauflösung:''' Damit die Nockenwerte der vorhandenen elektronischen Nockensteuerung im neuen Datenbaustein wiederverwendet werden können, muss die virtuelle Geberauflösung auf den Wert der vorhandenen elektronischen Nockensteuerung geändert werden.
+
*'''Virtual encoder resolution:''' If the cam values of the existing electronic cam control should be reused in the new data block, the virtual encoder resolution must be changed to the value of the existing electronic cam control.
*'''Art der Totzeitkompensation:''' Damit die Totzeiten der vorhandenen elektronischen Nockensteuerung im neuen Datenbaustein wiederverwendet werden können, muss die Art der Totzeit (Bitweise; Blockweise; ...) auf die von der vorhandenen elektronischen Nockensteuerung verwendeten Art geändert werden.
+
*'''Type of idle time compensation:''' If the idle time of the existing electronic cam control should be reused in the new data block, then the type of idle time (Bitwise; Blockwise; ...) has to be set accordingly.
*'''PROFIBUS-Slave-ID:''' Die gewünschte PROFIBUS-Slave-ID muss mit der Software WINLOC 32 eingestellt werden, wenn diese nicht über den PROFIBUS-Master zugewiesen werden soll. Im Auslieferungszustand ist die PROFIBUS-Slave-ID auf 126 eingestellt.
+
*'''PROFIBUS-Slave-ID:''' The desired PROFIBUS-Slave-ID has to be set via WINLOC 32 software, if this is not to be assigned via the PROFIBUS master. The PROFIBUS-Slave-ID is set to 126 at delivery state.
*'''Betriebs-Modi:''' In Verbindung mit einem PROFIBUS-Master muss dieser auf '''S7-Mode''' eingestellt sein. Im Auslieferungszustand ist der S7-Mode bereits eingestellt.  
+
*'''Operation modes:''' In conjunction with a PROFIBUS-Master this must be set to '''S7-mode'''. This S7-mode is already set at delivery state.  
*'''Logik:''' Wenn im Altgerät die Logikfunktion verwendet wird, muss diese im ROTARNOCK 100-PB noch freigeschaltet werden. Dafür wird ein Freischaltcode benötigt, der kostenpflichtig ist. '''Achtung:''' Der Freischaltcode für die Logikfunktion ist an die Serien-Nr. gebunden und kann daher nicht für andere elektronische Nockensteuerungen verwendet werden.
+
*'''Logic function:''' If the logic function is used in the old device then this function has to be unlocked for ROTARNOCK 100-PB. Therefore a chargeable release code is needed. '''Attention:''' This release code is bounded to the serial-no. and can not be used for other cam controls.
  
==SPS Projekt==
+
==SPS Project==
*'''GSD-Datei:''' Um das ROTARNOCK 100-PB in das Projekt einbinden zu können, muss die GSD-Datei [[#Weblinks|'''(R100.GSD)''']] in die Steuerung geladen werden.
+
*'''GSD-file:''' In order to integrate ROTARNOCK 100-PB into a project, the GSD-file [[#Weblinks|'''(R100.GSD)''']] has to be loaded in the cam control.
*'''AWL-Datei:''' Die im Projekt befindliche AWL-Datei, die im Datenbaustein abgebildet wird, muss durch eine für ROTARNOCK 100-PB passende AWL-Datei ersetzt werden. Dazu muss der [[Datenbausteingenerator]]2 verwendet werden.
+
*'''AWL-file:''' The AWL-file contained in the project which is pictured in the data block has to be replaced by an AWL-file fitting for ROTARNOCK 100-PB. Herefore has to be used the [[Data component generator]]2.
  
 
==Weblinks==
 
==Weblinks==
*[https://www.deutschmann.de/downloads/Marketing/Anleitung-Instructions/Handbuecher-Manuals/Nockenschaltwerke%20-%20Cam%20Controls/ROTARNOCK%20100/German/ROTARNOCK_100.pdf Handbuch für das ROTARNOCK 100] (PDF-Datei)
+
*[https://www.deutschmann.de/downloads/Marketing/Anleitung-Instructions/Handbuecher-Manuals/Nockenschaltwerke%20-%20Cam%20Controls/ROTARNOCK%20100/English/ROTARNOCK_100_e.pdf Manual for ROTARNOCK 100] (PDF-file)
*[https://www.deutschmann.de/downloads/Support/Profibus/R100.GSD GSD-Datei für das ROTARNOCK 100-PB]  
+
*[https://www.deutschmann.de/downloads/Support/Profibus/R100.GSD GSD-file for ROTARNOCK 100-PB]  
*Handbuch [https://www.deutschmann.de/downloads/Marketing/Anleitung-Instructions/Handbuecher-Manuals/Nockenschaltwerke%20-%20Cam%20Controls/NSW%20mit%20Feldbus-CamControlWithFieldbusConnection/German/NSWmitFeldbus.pdf Nockensteuerungen mit Feldbusanbindung] (PDF-Datei)
+
*Manual [https://www.deutschmann.de/downloads/Marketing/Anleitung-Instructions/Handbuecher-Manuals/Nockenschaltwerke%20-%20Cam%20Controls/NSW%20mit%20Feldbus-CamControlWithFieldbusConnection/English/CamControlsWithFieldbusConnection.pdf Cam controls with fieldbus connection] (PDF-file)
*Handbuch [https://www.deutschmann.de/downloads/Marketing/Anleitung-Instructions/Handbuecher-Manuals/Nockenschaltwerke%20-%20Cam%20Controls/L100,%20200,%20R80,%20100%20mit%20Feldbusanbindung-WithFieldbusConnection/German/L-R%20mit%20Feldbus_d.pdf ROTARNOCK 100 mit Feldbusanbindung] (PDF-Datei)
+
*Manual [https://www.deutschmann.de/downloads/Marketing/Anleitung-Instructions/Handbuecher-Manuals/Nockenschaltwerke%20-%20Cam%20Controls/L100,%20200,%20R80,%20100%20mit%20Feldbusanbindung-WithFieldbusConnection/English/L-R%20mit%20Feldbus-e.pdf ROTARNOCK 100 with fieldbus connection] (PDF-file)

Aktuelle Version vom 1. Dezember 2020, 14:55 Uhr

ROTARNOCK 1-PB, ROTARNOCK 2-PB and ROTARNOCK 80-PB can be replaced by ROTARNOCK 100-PB . As an 1:1 exchange is not possible, the following points have to be noted:

Device Configuration

The configuration has to be done with our software WINLOC 32-Basis-or Comfort version. Herefore is needed a corresponding Programming cable. Note: Whether the programming cable can also be used for a necessary read-out of the old device has to be tested in each case! Attention: For the configuration, the PC is in need of a real COM-Port. If there is no real COM-Port at the PC, then an USB-to-RS232 converter has to be used.

  • Virtual encoder resolution: If the cam values of the existing electronic cam control should be reused in the new data block, the virtual encoder resolution must be changed to the value of the existing electronic cam control.
  • Type of idle time compensation: If the idle time of the existing electronic cam control should be reused in the new data block, then the type of idle time (Bitwise; Blockwise; ...) has to be set accordingly.
  • PROFIBUS-Slave-ID: The desired PROFIBUS-Slave-ID has to be set via WINLOC 32 software, if this is not to be assigned via the PROFIBUS master. The PROFIBUS-Slave-ID is set to 126 at delivery state.
  • Operation modes: In conjunction with a PROFIBUS-Master this must be set to S7-mode. This S7-mode is already set at delivery state.
  • Logic function: If the logic function is used in the old device then this function has to be unlocked for ROTARNOCK 100-PB. Therefore a chargeable release code is needed. Attention: This release code is bounded to the serial-no. and can not be used for other cam controls.

SPS Project

  • GSD-file: In order to integrate ROTARNOCK 100-PB into a project, the GSD-file (R100.GSD) has to be loaded in the cam control.
  • AWL-file: The AWL-file contained in the project which is pictured in the data block has to be replaced by an AWL-file fitting for ROTARNOCK 100-PB. Herefore has to be used the Data component generator2.

Weblinks