Device replacement ROTARNOCK 1, 2, 3 and 4 (English): Unterschied zwischen den Versionen
Zur Navigation springen
Zur Suche springen
Grund (Diskussion | Beiträge) (Die Seite wurde neu angelegt: „== Device replacement == The following information and components are needed to guarantee a quick exchange and programming of the new device: '''Adapting the…“) |
Reith (Diskussion | Beiträge) |
||
(16 dazwischenliegende Versionen von 3 Benutzern werden nicht angezeigt) | |||
Zeile 1: | Zeile 1: | ||
− | + | Rotarnock 1,2,3 and 4 as well as the corresponding PROFIBUS variants were replaced by [[ROTARNOCK 100 (English)|ROTARNOCK 100]]. This is available with or without PROFIBUS. The following information and components are needed to guarantee a quick exchange and programming of the new device: | |
− | The following information and components are needed to guarantee a quick exchange and programming of the new device: | + | # The serial number or the article number (Vxxxx) of the old device have to be known to ensure that an appropriate new device can be offered. |
− | + | # If a TERM 6 or a TERM 24 is already in use, we also need to know the serial number of this device to check the compatibility with the new device. '''Note''': TERM 5 is '''not''' compatible with ROTARNOCK 100! | |
− | + | # To read-out the old device and possibly for the configuration and programming of the new device with the WINLOC32-Basis-or comfort-version, a corresponding [[Programming cable]] is needed. '''Note''': Whether the programming cable can also be used for a necessary read-out of the old device has to be tested in each case! | |
− | + | # A TERM 6 or the WINLOC32-Basis or comfort-version is needed for the configuration of the new device. | |
− | # The serial number or the article number ( | ||
− | # To read-out the old device and possibly for the configuration and programming of the new device with the WINLOC32-Basis-or comfort-version, a corresponding | ||
− | # A TERM 6 or the WINLOC32-Basis or comfort-version | ||
# There has to be a real COM-Port on the PC for the configuration and programming of the new device with WINLOC32. If there is no real COM-Port on the PC, you need a USB-RS232-converter. | # There has to be a real COM-Port on the PC for the configuration and programming of the new device with WINLOC32. If there is no real COM-Port on the PC, you need a USB-RS232-converter. | ||
− | + | === Programming - zero offset - program selection === | |
− | + | # The programming of the new device can be performed with TERM 6, TERM 24 or with the WINLOC32-Basis or comfort-version. With the PROFIBUS version you can also program via PROFIBUS. | |
− | + | # The zero offset can be performed with TERM 6, TERM 24 or with the WINLOC32-comfort-version. With the PROFIBUS version you can also program via PROFIBUS. | |
− | + | # The program selection can be done with TERM 6, TERM 24 or via the external program selection. With the PROFIBUS version you can also program via PROFIBUS. | |
− | # The programming of the device can be performed with | + | '''For a corresponding offer please let us know the serial number or the article number (Vxxxx) of the old device and, if used, the serial-no. of TERM 6 resp. TERM 24.''' |
− | # The zero offset can be performed with | ||
− | # The program selection can be done with | ||
− | |||
− | |||
− | |||
− | '''For a corresponding offer please let us know the serial number or the article number ( |
Aktuelle Version vom 27. August 2019, 13:28 Uhr
Rotarnock 1,2,3 and 4 as well as the corresponding PROFIBUS variants were replaced by ROTARNOCK 100. This is available with or without PROFIBUS. The following information and components are needed to guarantee a quick exchange and programming of the new device:
- The serial number or the article number (Vxxxx) of the old device have to be known to ensure that an appropriate new device can be offered.
- If a TERM 6 or a TERM 24 is already in use, we also need to know the serial number of this device to check the compatibility with the new device. Note: TERM 5 is not compatible with ROTARNOCK 100!
- To read-out the old device and possibly for the configuration and programming of the new device with the WINLOC32-Basis-or comfort-version, a corresponding Programming cable is needed. Note: Whether the programming cable can also be used for a necessary read-out of the old device has to be tested in each case!
- A TERM 6 or the WINLOC32-Basis or comfort-version is needed for the configuration of the new device.
- There has to be a real COM-Port on the PC for the configuration and programming of the new device with WINLOC32. If there is no real COM-Port on the PC, you need a USB-RS232-converter.
Programming - zero offset - program selection
- The programming of the new device can be performed with TERM 6, TERM 24 or with the WINLOC32-Basis or comfort-version. With the PROFIBUS version you can also program via PROFIBUS.
- The zero offset can be performed with TERM 6, TERM 24 or with the WINLOC32-comfort-version. With the PROFIBUS version you can also program via PROFIBUS.
- The program selection can be done with TERM 6, TERM 24 or via the external program selection. With the PROFIBUS version you can also program via PROFIBUS.
For a corresponding offer please let us know the serial number or the article number (Vxxxx) of the old device and, if used, the serial-no. of TERM 6 resp. TERM 24.