Device replacement ROTARNOCK 1, 2, 3 and 4 (English): Unterschied zwischen den Versionen

Aus Deutschmann Wiki
Zur Navigation springen Zur Suche springen
Zeile 1: Zeile 1:
 
Rotarnock 1,2,3 and 4 as well as the corresponding PROFIBUS variants were replaced by [[ROTARNOCK 100 (English)|ROTARNOCK 100]]. This is available with or without PROFIBUS. The following information and components are needed to guarantee a quick exchange and programming of the new device:
 
Rotarnock 1,2,3 and 4 as well as the corresponding PROFIBUS variants were replaced by [[ROTARNOCK 100 (English)|ROTARNOCK 100]]. This is available with or without PROFIBUS. The following information and components are needed to guarantee a quick exchange and programming of the new device:
 
# The serial number or the article number (Vxxxx) of the old device have to be known to ensure that an appropriate new device can be offered.
 
# The serial number or the article number (Vxxxx) of the old device have to be known to ensure that an appropriate new device can be offered.
# If a TERM 6 oder a TERM 24 is already in use, we also need to know the serial number of this device to check the compatibility with the new device. '''Note''': TERM 5 is '''not''' compatible with ROTARNOCK 100!
+
# If a TERM 6 or a TERM 24 is already in use, we also need to know the serial number of this device to check the compatibility with the new device. '''Note''': TERM 5 is '''not''' compatible with ROTARNOCK 100!
 
# To read-out the old device and possibly for the configuration and programming of the new device with the WINLOC32-Basis-or comfort-version, a corresponding [[Programming cable]] is needed. '''Note''': Whether the programming cable can also be used for a necessary read-out of the old device has to be tested in each case!
 
# To read-out the old device and possibly for the configuration and programming of the new device with the WINLOC32-Basis-or comfort-version, a corresponding [[Programming cable]] is needed. '''Note''': Whether the programming cable can also be used for a necessary read-out of the old device has to be tested in each case!
 
# A TERM 6 or the WINLOC32-Basis or comfort-version is needed for the configuration of the new device.
 
# A TERM 6 or the WINLOC32-Basis or comfort-version is needed for the configuration of the new device.

Version vom 27. August 2019, 12:56 Uhr

Rotarnock 1,2,3 and 4 as well as the corresponding PROFIBUS variants were replaced by ROTARNOCK 100. This is available with or without PROFIBUS. The following information and components are needed to guarantee a quick exchange and programming of the new device:

  1. The serial number or the article number (Vxxxx) of the old device have to be known to ensure that an appropriate new device can be offered.
  2. If a TERM 6 or a TERM 24 is already in use, we also need to know the serial number of this device to check the compatibility with the new device. Note: TERM 5 is not compatible with ROTARNOCK 100!
  3. To read-out the old device and possibly for the configuration and programming of the new device with the WINLOC32-Basis-or comfort-version, a corresponding Programming cable is needed. Note: Whether the programming cable can also be used for a necessary read-out of the old device has to be tested in each case!
  4. A TERM 6 or the WINLOC32-Basis or comfort-version is needed for the configuration of the new device.
  5. There has to be a real COM-Port on the PC for the configuration and programming of the new device with WINLOC32. If there is no real COM-Port on the PC, you need a USB-RS232-converter.

Programming - zero offset - program selection

  1. The programming of the new device can be performed with a TERM 6, a TERM 24 or with the WINLOC32-Basis or comfort-version. With the PROFIBUS version you can also program via the PROFIBUS.
  2. The zero offset can be performed with a TERM 6, a TERM 24 or with the WINLOC32-comfort-version. With the PROFIBUS version you can also program via the PROFIBUS.
  3. The program selection can be done with a TERM 6, a TERM 24 or via the external program selection. With the PROFIBUS version you can also program via the PROFIBUS.

For a corresponding offer please let us know the serial number or the article number (Vxxxx) of the old device and, if used, the serial-no. of TERM 6 resp. TERM 24.