LOCON 100 (English): Unterschied zwischen den Versionen

Aus Deutschmann Wiki
Zur Navigation springen Zur Suche springen
Zeile 2: Zeile 2:
 
== Configuration ==
 
== Configuration ==
 
By factory setting '''all''' LOCON 100 cam controls are configured as follows:
 
By factory setting '''all''' LOCON 100 cam controls are configured as follows:
−
*outputs: '''16'''
+
*Outputs: '''16'''
 
*Encoder type: '''SSI Singleturn'''
 
*Encoder type: '''SSI Singleturn'''
−
*real encoder resolution: '''4096'''
+
*Real encoder resolution: '''4096'''
−
*virtual encoder resolution: '''4096'''
+
*Virtual encoder resolution: '''4096'''
−
*idle time: '''Bitwise'''
+
*Idle time: '''Bitwise'''
 
This configuration set by default may be changed by using [[TERM 6]] or the software [[WINLOC 32]].
 
This configuration set by default may be changed by using [[TERM 6]] or the software [[WINLOC 32]].
 
== Programming ==
 
== Programming ==
Zeile 62: Zeile 62:
 
If the rotary coding switch is on position "'''00'''" und "'''7E'''" then any desired address can be assigned wither through WINLOC32 or the PROFIBUS-Master.
 
If the rotary coding switch is on position "'''00'''" und "'''7E'''" then any desired address can be assigned wither through WINLOC32 or the PROFIBUS-Master.
 
The [[#Weblinks|'''GSD-file''' (L100.GSD)]] and a [[#Weblinks|'''S7-example project''']] are available for download on our homepage.
 
The [[#Weblinks|'''GSD-file''' (L100.GSD)]] and a [[#Weblinks|'''S7-example project''']] are available for download on our homepage.
−
Weitere Informationen zum LOCON 100-PB sind dem Handbuch [[#Weblinks|Nockensteuerungen mit Feldbusanbindung]] zu entnehmen.
+
Further information regarding LOCON 100-PB can be found in the manual [[#Weblinks|Cam Controls with Fieldbus-Connection]].
 
=== LOCON 100-MB (Modbus) ===
 
=== LOCON 100-MB (Modbus) ===
−
Das LOCON 100-MB (Modbus) ist '''immer''' ein Modbus-RTU-Slave und ist '''nur''' in der '''2-Draht-Variante''' erhältlich. Das LOCON 100-MB verfügt über eine RS232 Standard Schnittstelle sowie über eine RS232-(Modbus-RTU) Schnittstelle und eine RS485-(Modbus-RTU) Schnittstelle, die entsprechend über den  Drehkodierschalter ''High'' auf der Geräterückseite eingestellt werden können.
+
LOCON 100-MB (Modbus) is '''always''' a Modbus-RTU-Slave and is '''only''' available in the '''2-core cable-version'''. LOCON 100-MB features a RS232-Standard-Interface as well as a RS232-(Modbus-RTU) Interface and a RS485-(Modbus-RTU) Interface, which can be changed by adjusting the rotary coding switch ''High'' located at the bottom side of the device.
 
{| class="wikitable"
 
{| class="wikitable"
−
|+Schalterstellung
+
|+Switch position
 
|-
 
|-
−
! High !! Low !! Bedeutung
+
! High !! Low !! Meaning
 
|-
 
|-
 
| C || x || RS232-Modbus (X = ModbusSlave-ID)
 
| C || x || RS232-Modbus (X = ModbusSlave-ID)
 
|-
 
|-
−
| D || x || RS485-Modbus ohne Busabschluss (x = Modbus-Slave-ID)
+
| D || x || RS485-Modbus without bus termination (x = Modbus-Slave-ID)
 
|-
 
|-
−
| E || x || RS485-Modbus mit aktiviertem Busabschluss (x = Modbus-Slave-ID)
+
| E || x || RS485-Modbus with activated bus termination (x = Modbus-Slave-ID)
 
|-
 
|-
−
| F || x || RS232-Standard Schnittstelle
+
| F || x || RS232-Standard Interface
 
|}
 
|}
−
'''Hinweis:''' Es werden '''nur''' die Modbus-Adressen '''1 ... 15''' (Dezimal) unterstützt (rechter Drehkodierschalter ''Low'' = ID). Die Broadcastadresse '''0''' wird '''nicht''' unterstützt. Die Einstellung über den Drehkodierschalter erfolgt in ''hexadezimal''.<br />
+
'''Note:''' '''Only''' Modbus-Addresses '''1 ... 15''' (decimal) are supported (right rotary coding switch ''Low'' = ID). The Broadcastaddress '''0''' is '''not''' supported. The Setting via the rotary coding switch is done ''hexadecimal''.<br />
−
Folgende Modbus-RTU-Kommandos werden von dem Gerät unterstützt:   
+
Following Modbus-RTU-commands are supported by the device:   
 
{| class="wikitable"
 
{| class="wikitable"
−
|+Modbus-RTU-Kommandos
+
|+Modbus-RTU-commands
 
|-
 
|-
−
! Kommando !! Bedeutung
+
! command !! meaning
 
|-
 
|-
 
| 03 || (0x03) Read Holding Registers  
 
| 03 || (0x03) Read Holding Registers  
Zeile 89: Zeile 89:
 
| 16 || (0x10) Preset Multiple Regs
 
| 16 || (0x10) Preset Multiple Regs
 
|}
 
|}
−
Die Übertragungsbaudrate beträgt '''19200 Baud'''; '''No Parity'''.   
+
The transmission baud rate is '''19200 Baud'''; '''No Parity'''.   
−
Weitere Informationen zum LOCON 100-MB sind dem Kapitel 8 ''LOCON 100 mit Modbus'' aus dem [[#Weblinks|Handbuch für das LOCON 100]] zu entnehmen.  
+
Further Information regarding LOCON 100-MB can be found in chapter 8 ''LOCON 100 with Modbus'' of the [[#Weblinks|Manual for LOCON 100]].  
−
== LOCON 100-Out I/O32 (Erweiterungsmodul) ==
+
== LOCON 100-Out I/O32 (Extension module) ==
−
Das LOCON 100-Out I/O32 ist ein '''Erweiterungsmodul''' und verfügt über 32 I/Os. Damit kann das LOCON 100 bzw. (-PB)) auf 48 I/Os (inkl. der 16 I/Os des LOCON 100 bzw. (-PB)) erweitert werden. Das LOCON 100-Out I/O32 enthält '''keinen''' eigenen Prozessor. Dadurch ist die Schaltgenauigkeit (Zykluszeit) abhängig vom LOCON 100 bzw. (-PB)).
+
LOCON 100-Out I/O32 is an '''extension module''' and contains 32 I/Os. With this extension module the basic device LOCON 100 resp. (-PB)) is expanded to a total of 48 I/Os (incl. 16 I/Os of LOCON 100 bzw. (-PB)). LOCON 100-Out I/O32 does '''not''' contain an own processor. Therefore, the switching accuracy (cycle time) depends on the LOCON 100 bzw. (-PB)).
 
== Weblinks ==
 
== Weblinks ==
 
*[http://www.deutschmann.de/produkte/download.php?file_id=285 Handbuch für das LOCON 100] (PDF-Datei)
 
*[http://www.deutschmann.de/produkte/download.php?file_id=285 Handbuch für das LOCON 100] (PDF-Datei)

Version vom 15. Mai 2014, 11:29 Uhr

LOCON 100 und Erweiterungsmodul LOCON 100-Out I/O32

Configuration

By factory setting all LOCON 100 cam controls are configured as follows:

  • Outputs: 16
  • Encoder type: SSI Singleturn
  • Real encoder resolution: 4096
  • Virtual encoder resolution: 4096
  • Idle time: Bitwise

This configuration set by default may be changed by using TERM 6 or the software WINLOC 32.

Programming

LOCON 100 can be programmed by TERM 6 or TERM 24 or the software WINLOC 32. The PROFIBUS-Version can be programmed also by PROFIBUS. The Modbus-version can by programmed by Modbus.

device versions

LOCON 100

LOCON 100 features a serial RS232-interface and a RS485-(DICNET) interface, the needed setting is made through the corresponding rotary coding switches High und Low , located at the bottom side of the device.

Switch position
High Low Meaning
D DICNET-Address DICNET-Operation, Bus Termination inactive
E DICNET-Address DICNET-Operation, Bus Termination active
F F RS232-Operation

Only the DICNET-Addresses 0 ... 15 (decimal) are supported (right Rotary coding switch Low = DICNET-Address). Examples:

Switch Position
High Low Meaning
D 3 bus termination inactive, DICNET-Address 3
E C bus termination active, DICNET-Address 12

Note: The setting via the rotary coding switches is done in hexadecimal.

LOCON 100-PB (PROFIBUS)

LOCON 100-PB (PROFIBUS) is always PROFIBUS-Slave and features a serial RS232-interface and a PROFIBUS-Interface, instead of the RS485-(DICNET) Interface, the needed setting is made through the corresponding rotary coding switches High und Low , located at the bottom side of the device.

Switch Position
High Low Meaning
0 0 PROFIBUS-operation, external address assignment
0 1 PROFIBUS-operation, Address 1
…
7 D PROFIBUS-operation, Address 125
7 E PROFIBUS-operation, external address assignment
F F RS232-operation

Note: The setting via the rotary coding switches is done in hexadecimal.
In LOCON 100-PB two modes are selectable through WINLOC32 via the PROFIBUS-Interface.

The PROFIBUS-Address (Slave-ID) is set by factory Setting on 126 (decimal). If the rotary coding switch is on position "00" und "7E" then any desired address can be assigned wither through WINLOC32 or the PROFIBUS-Master. The GSD-file (L100.GSD) and a S7-example project are available for download on our homepage. Further information regarding LOCON 100-PB can be found in the manual Cam Controls with Fieldbus-Connection.

LOCON 100-MB (Modbus)

LOCON 100-MB (Modbus) is always a Modbus-RTU-Slave and is only available in the 2-core cable-version. LOCON 100-MB features a RS232-Standard-Interface as well as a RS232-(Modbus-RTU) Interface and a RS485-(Modbus-RTU) Interface, which can be changed by adjusting the rotary coding switch High located at the bottom side of the device.

Switch position
High Low Meaning
C x RS232-Modbus (X = ModbusSlave-ID)
D x RS485-Modbus without bus termination (x = Modbus-Slave-ID)
E x RS485-Modbus with activated bus termination (x = Modbus-Slave-ID)
F x RS232-Standard Interface

Note: Only Modbus-Addresses 1 ... 15 (decimal) are supported (right rotary coding switch Low = ID). The Broadcastaddress 0 is not supported. The Setting via the rotary coding switch is done hexadecimal.
Following Modbus-RTU-commands are supported by the device:

Modbus-RTU-commands
command meaning
03 (0x03) Read Holding Registers
16 (0x10) Preset Multiple Regs

The transmission baud rate is 19200 Baud; No Parity. Further Information regarding LOCON 100-MB can be found in chapter 8 LOCON 100 with Modbus of the Manual for LOCON 100.

LOCON 100-Out I/O32 (Extension module)

LOCON 100-Out I/O32 is an extension module and contains 32 I/Os. With this extension module the basic device LOCON 100 resp. (-PB)) is expanded to a total of 48 I/Os (incl. 16 I/Os of LOCON 100 bzw. (-PB)). LOCON 100-Out I/O32 does not contain an own processor. Therefore, the switching accuracy (cycle time) depends on the LOCON 100 bzw. (-PB)).

Weblinks

Abgerufen von „http://wiki.deutschmann.de/index.php?title=LOCON_100_(English)&oldid=1228“