LOCON 200 (English): Unterschied zwischen den Versionen
Reith (Diskussion | Beiträge) |
Reith (Diskussion | Beiträge) |
||
Zeile 9: | Zeile 9: | ||
This configuration set by default may be changed by using [[TERM 6]] or the software [[WINLOC 32]]. | This configuration set by default may be changed by using [[TERM 6]] or the software [[WINLOC 32]]. | ||
== Programming == | == Programming == | ||
− | LOCON 200 can be programmed by TERM 6 or [[TERM 24]] or the software WINLOC 32. | + | LOCON 200 can be programmed by TERM 6 or [[TERM 24]] or the software WINLOC 32. The PROFIBUS-Version can be programmed also by PROFIBUS. |
− | == | + | == Device versions == |
=== LOCON 200 === | === LOCON 200 === | ||
− | + | LOCON 200 features a serial RS232-interface and a RS485-([[DICNET]]) interface, the needed setting is made through the corresponding rotary coding switches ''High'' und ''Low'' , located at the bottom side of the device. | |
{| class="wikitable" | {| class="wikitable" | ||
− | |+ | + | |+Switch Position |
|- | |- | ||
− | ! High !! Low !! | + | ! High !! Low !! Meaning |
|- | |- | ||
− | | D || DICNET- | + | | D || DICNET-Adress || DICNET-Operation, Bus Termination inactive |
|- | |- | ||
− | | E || DICNET- | + | | E || DICNET-Adress || DICNET-Operation, Bus Termination active |
|- | |- | ||
− | | F || F || RS232- | + | | F || F || RS232-Operation |
|} | |} | ||
− | + | '''Only''' the DICNET-Addresses '''0 ... 15''' (decimal) are supported (right rotary coding switch ''Low'' = DICNET-Address). Examples: | |
{| class="wikitable" | {| class="wikitable" | ||
|+Schalterstellung | |+Schalterstellung |
Version vom 15. Mai 2014, 14:39 Uhr
Inhaltsverzeichnis
Konfiguration
By factory setting all LOCON 200 cam controls are configured as follows:
- Outputs: 16
- Encoder Type: SSI Singleturn
- Real Encoder resolution: 4096
- Virtual Encoder resolution: 4096
- Idle time: Bitwise
This configuration set by default may be changed by using TERM 6 or the software WINLOC 32.
Programming
LOCON 200 can be programmed by TERM 6 or TERM 24 or the software WINLOC 32. The PROFIBUS-Version can be programmed also by PROFIBUS.
Device versions
LOCON 200
LOCON 200 features a serial RS232-interface and a RS485-(DICNET) interface, the needed setting is made through the corresponding rotary coding switches High und Low , located at the bottom side of the device.
High | Low | Meaning |
---|---|---|
D | DICNET-Adress | DICNET-Operation, Bus Termination inactive |
E | DICNET-Adress | DICNET-Operation, Bus Termination active |
F | F | RS232-Operation |
Only the DICNET-Addresses 0 ... 15 (decimal) are supported (right rotary coding switch Low = DICNET-Address). Examples:
High | Low | Bedeutung |
---|---|---|
D | 3 | Busabschluss inaktiv, DICNET-Adresse 3 |
E | C | Busabschluss aktiv, DICNET-Adresse 12 |
Hinweis: Die Einstellung über die Drehkodierschalter erfolgt in hexadezimal.
LOCON 200-PB (PROFIBUS)
Das LOCON 200-PB (PROFIBUS) ist immer PROFIBUS-Slave und verfügt über eine serielle RS232-Schnittstelle und über eine PROFIBUS-Schnittstelle, anstelle der RS485-(DICNET) Schnittstelle, die entsprechend über die beiden Drehkodierschalter High und Low auf der Geräterückseite eingestellt werden können.
High | Low | Bedeutung |
---|---|---|
0 | 0 | PROFIBUS-Betrieb, externe Adressvergabe |
0 | 1 | PROFIBUS-Betrieb, Adresse 1 |
… | ||
7 | D | PROFIBUS-Betrieb, Adresse 125 |
7 | E | PROFIBUS-Betrieb, externe Adressvergabe |
F | F | RS232-Betrieb |
Hinweis: Die Einstellung über die Drehkodierschalter erfolgt in hexadezimal.
Bei Betrieb über die PROFIBUS-Schnittstelle sind im LOCON 200-PB zwei Modi über WINLOC 32 auswählbar.
- S7-Modus (Auslieferungszustand): Zum Betrieb an einer Simatic S7 und zur Verwendung des Datenbausteinsimulators.
- Kommunikationsprofilmodus: Zum Betrieb über das Kommunikationsprofil für Deutschmann Nockensteuerungen.
Die PROFIBUS-Adresse (Slave-ID) ist im Auslieferungszustand auf 126 (dezimal) eingestellt. In den Schalterstellungen "00" und "7E" kann über WINLOC 32 oder den PROFIBUS-Master eine beliebige Adresse vergeben werden. Die GSD-Datei (L200.GSD) und ein S7-Beispielprojekt stehen zum Download zur Verfügung. Weitere Informationen zum LOCON 200-PB sind dem Handbuch Nockensteuerungen mit Feldbusanbindung zu entnehmen.
LOCON 200-Out I/O8 (Erweiterungsmodul)
Das LOCON 200-Out I/O8 ist ein Erweiterungsmodul und verfügt über 8 I/Os. Damit kann das LOCON 200 bzw. (-PB)) schrittweise bis zu einer maximalen Ausbaustufe von 144 I/Os (inkl. der 16 I/Os des LOCON 200 bzw. (-PB)) erweitert werden. Das LOCON 200-Out I/O8 enthält einen eigenen Prozessor. Dadurch ist die Schaltgenauigkeit (Zykluszeit) unabhängig vom LOCON 200 bzw. (-PB)).
Weblinks
- Handbuch für das LOCON 200 (PDF-Datei)
- GSD-Datei für das LOCON 200-PB
- S7-Beispiel-Projekt (ZIP-Datei)
- Handbuch Kommunikationsprofil für Deutschmann Nockensteuerungen (PDF-Datei)
- Handbuch Nockensteuerungen mit Feldbusanbindung (PDF-Datei)