LOCON 200 (English): Unterschied zwischen den Versionen

Aus Deutschmann Wiki
Zur Navigation springen Zur Suche springen
(17 dazwischenliegende Versionen von 3 Benutzern werden nicht angezeigt)
Zeile 1: Zeile 1:
[[Datei:LOCON200_LOCON200_IO8.jpg|thumb|LOCON 200 und Erweiterungsmodul LOCON 200-Out I/O8]]
+
[[Datei:LOCON200_LOCON200_IO8.jpg|thumb|LOCON 200 and extension module LOCON 200-Out I/O8]]
== Konfiguration ==
+
== Configuration ==
 
By factory setting '''all''' LOCON 200 cam controls are configured as follows:
 
By factory setting '''all''' LOCON 200 cam controls are configured as follows:
 
*Outputs: '''16'''
 
*Outputs: '''16'''
Zeile 7: Zeile 7:
 
*Virtual Encoder resolution: '''4096'''
 
*Virtual Encoder resolution: '''4096'''
 
*Idle time: '''Bitwise'''
 
*Idle time: '''Bitwise'''
This configuration set by default may be changed by using [[TERM 6]] or the software [[WINLOC 32]].
+
This configuration set by default may be changed by using [[TERM 6 (English)|TERM 6]] or the software [[WINLOC 32 (English)|WINLOC 32]].
 +
 
 
== Programming ==
 
== Programming ==
LOCON 200 can be programmed by TERM 6 or [[TERM 24]] or the software WINLOC 32.  The PROFIBUS-Version can be programmed also by PROFIBUS.
+
LOCON 200 can be programmed by TERM 6 or [[TERM 24 (English)|TERM 24]] or the software WINLOC 32.  The PROFIBUS-Version can be programmed also via PROFIBUS.
 +
 
 
== Device versions ==
 
== Device versions ==
 
=== LOCON 200 ===
 
=== LOCON 200 ===
LOCON 200 features a serial RS232-interface and a RS485-([[DICNET]]) interface, the needed setting is made through the corresponding rotary coding switches ''High'' und ''Low'' , located at the bottom side of the device.
+
LOCON 200 features a serial RS232-interface and a RS485-([[DICNET (English)|DICNET]]) interface, the needed setting is made through the corresponding rotary coding switches ''High'' und ''Low'', located at the bottom side of the device.
 
{| class="wikitable"
 
{| class="wikitable"
 
|+Switch Position
 
|+Switch Position
Zeile 30: Zeile 32:
 
! High !! Low !! Meaning
 
! High !! Low !! Meaning
 
|-
 
|-
| D || 3 || Busabschluss inaktiv, DICNET-Adresse '''3'''
+
| D || 3 || bus termination inactive, DICNET-Address '''3'''
 
|-
 
|-
| E || C || Busabschluss aktiv, DICNET-Adresse '''12'''
+
| E || C || bus termination active, DICNET-Address '''12'''
 
|}
 
|}
'''Hinweis:''' Die Einstellung über die Drehkodierschalter erfolgt in ''hexadezimal''.
+
''''Note:''' The setting via the rotary coding switches is done in ''hexadecimal''.
 +
 
 
=== LOCON 200-PB (PROFIBUS) ===
 
=== LOCON 200-PB (PROFIBUS) ===
Das LOCON 200-PB (PROFIBUS) ist '''immer''' PROFIBUS-Slave und verfügt über eine serielle RS232-Schnittstelle und über eine PROFIBUS-Schnittstelle, anstelle der RS485-(DICNET) Schnittstelle, die entsprechend über die beiden Drehkodierschalter ''High'' und ''Low'' auf der Geräterückseite eingestellt werden können.  
+
LOCON 200-PB (PROFIBUS) is '''always''' PROFIBUS-Slave and features a serial RS232-interface and a PROFIBUS-Interface, instead of the RS485-(DICNET) Interface, the needed setting is made through the corresponding rotary coding switches ''High'' und ''Low'', located at the bottom side of the device.  
 
{| class="wikitable"
 
{| class="wikitable"
|+Schalterstellung
+
|+Switch Position
 
|-
 
|-
! High !! Low !! Bedeutung
+
! High !! Low !! Meaning
 
|-
 
|-
| 0 || 0 || PROFIBUS-Betrieb, externe Adressvergabe
+
| 0 || 0 || PROFIBUS-operation, external address assignment 
 
|-
 
|-
| 0 || 1 || PROFIBUS-Betrieb, Adresse 1
+
| 0 || 1 || PROFIBUS-operation, Adress 1
 
|-
 
|-
 
|colspan="3" align="center"| …
 
|colspan="3" align="center"| …
 
|-
 
|-
| 7 || D || PROFIBUS-Betrieb, Adresse 125
+
| 7 || D || PROFIBUS-operation, Adress 125
 +
|-
 +
| 7 || E || PROFIBUS-operation, external address assignment
 +
|-
 +
| F || F || RS232-operation
 +
|}
 +
'''Note:'''  The setting via the rotary coding switches is done in ''hexadecimal''.<br />
 +
In LOCON 200-PB two modes are selectable through WINLOC32 via the PROFIBUS-Interface.
 +
* '''S7-Modus''' (ex-works condition): For an operation at a Simatic S7 and for use of the [[Data component simulator]].
 +
* '''Communication Profile Mode''': For the Operation via the [[#Weblinks|Communication Profile for Deutschmann cam controls]].
 +
The PROFIBUS-Address (Slave-ID) is set on 126 (decimal) in the factory setting.
 +
If the rotary coding switch is on position "'''00'''" und "'''7E'''" then any desired address can be assigned either through WINLOC32 or the PROFIBUS-Master.
 +
The [[#Weblinks|'''GSD-file''' (L200.GSD)]] and a [[#Weblinks|'''S7-example project''']] are available for download on our homepage.
 +
Further information regarding LOCON 200-PB can be found in the manual [[#Weblinks|Cam Controls with Fieldbus-Connection]].
 +
=== LOCON 200-MB (Modbus) ===
 +
LOCON 200-MB (Modbus) is '''always''' a Modbus-RTU-Slave and is '''only''' available in the '''2-core cable-version'''. LOCON 200-MB features a RS232-Standard-Interface as well as a RS232-(Modbus-RTU) Interface and a RS485-(Modbus-RTU) Interface, which can be changed by adjusting the rotary coding switch ''High'' located at the bottom side of the device.
 +
{| class="wikitable"
 +
|+Switch position
 +
|-
 +
! High !! Low !! Meaning
 +
|-
 +
| C || x || RS232-Modbus (X = ModbusSlave-ID)
 +
|-
 +
| D || x || RS485-Modbus without bus termination (x = Modbus-Slave-ID)
 +
|-
 +
| E || x || RS485-Modbus with activated bus termination (x = Modbus-Slave-ID)
 +
|-
 +
| F || x || RS232-Standard Interface
 +
|}
 +
'''Note:''' '''Only'''  Modbus-Addresses '''1 ... 15''' (decimal) are supported (right rotary coding switch ''Low'' = ID). The Broadcast address '''0''' is '''not''' supported. The Setting via the rotary coding switch is done in ''hexadecimal''.<br />
 +
The following Modbus-RTU-commands are supported by the device: 
 +
{| class="wikitable"
 +
|+Modbus-RTU-commands
 +
|-
 +
! command !! meaning
 
|-
 
|-
| 7 || E || PROFIBUS-Betrieb, externe Adressvergabe
+
| 03 || (0x03) Read Holding Registers
 
|-
 
|-
| F || F || RS232-Betrieb
+
| 16 || (0x10) Preset Multiple Regs
 
|}
 
|}
'''Hinweis:''' Die Einstellung über die Drehkodierschalter erfolgt in ''hexadezimal''.<br />
+
The transmission baud rate is '''19200 Baud'''; '''No Parity'''. Further information regarding LOCON 200-MB can be found in chapter ''LOCON 200 with Modbus'' of the [[#Weblinks|Manual for LOCON 200]].
Bei Betrieb über die PROFIBUS-Schnittstelle sind im LOCON 200-PB zwei Modi über WINLOC 32 auswählbar.
+
 
* '''S7-Modus''' (Auslieferungszustand): Zum Betrieb an einer Simatic S7 und zur Verwendung des [[Datenbausteinsimulator]]s.
+
===LOCON 200-Out I/O8 (extension module)===
* '''Kommunikationsprofilmodus''': Zum Betrieb über das [[#Weblinks|Kommunikationsprofil für Deutschmann Nockensteuerungen]].
+
LOCON 200-Out I/O8 is an '''extension module''' and contains 8 I/Os. With this extension module the basic device LOCON 200 resp. (-PB)/(-MB) can be expanded (depending on the version) by 8 I/Os step-by-step to a maximum configuration level of 144 I/Os (incl. the 16 I/Os of LOCON 200 resp. (-PB)/(-MB)). LOCON 200-Out I/O8 contains an own processor. Therefore, the switching accuracy (cycle time) is independent of the LOCON 200(-PB)/(-MB) Basic module.
Die PROFIBUS-Adresse (Slave-ID) ist im Auslieferungszustand auf 126 (dezimal) eingestellt.
+
 
In den Schalterstellungen "'''00'''" und "'''7E'''" kann über WINLOC 32 oder den PROFIBUS-Master eine beliebige Adresse vergeben werden.
+
=== NT Module for LOCON 200-Out I/O8 ===
Die [[#Weblinks|'''GSD-Datei''' (L200.GSD)]] und ein [[#Weblinks|'''S7-Beispielprojekt''']] stehen zum Download zur Verfügung.
+
The NT module for LOCON 200-Out I/O8 is a power supply that must be used for a configuration level step of more than 8 LOCON 200-Out I/O8 expansion modules.
Weitere Informationen zum LOCON 200-PB sind dem Handbuch [[#Weblinks|Nockensteuerungen mit Feldbusanbindung]] zu entnehmen.
+
The NT module must be inserted immediately after the LOCON 200 basic unit. Nothing can be connected to the NT module itself. The voltage supply of the NT module takes place via the 24V/DC of the LOCON 200 basic unit. The voltage supply of the then following LOCON 200-Out I/O8 expansion modules is adopted by the NT module
== LOCON 200-Out I/O8 (Erweiterungsmodul)==
+
 
Das LOCON 200-Out I/O8 ist ein '''Erweiterungsmodul''' und verfügt über 8 I/Os. Damit kann das LOCON 200 bzw. (-PB)) schrittweise bis zu einer maximalen Ausbaustufe von 144 I/Os (inkl. der 16 I/Os des LOCON 200 bzw. (-PB)) erweitert werden. Das LOCON 200-Out I/O8 enthält einen eigenen Prozessor. Dadurch ist die Schaltgenauigkeit (Zykluszeit) unabhängig vom LOCON 200 bzw. (-PB)).  
 
 
== Weblinks ==
 
== Weblinks ==
* [http://www.deutschmann.de/produkte/download.php?file_id=296 Handbuch für das LOCON 200] (PDF-Datei)
+
* [https://www.deutschmann.de/downloads/Marketing/Anleitung-Instructions/Handbuecher-Manuals/Nockenschaltwerke%20-%20Cam%20Controls/LOCON%20200/English/LOCON_200-e.pdf Manual for LOCON 200] (PDF-file)
* [http://www.deutschmann.de/produkte/download.php?file_id=272 GSD-Datei für das LOCON 200-PB]
+
* [https://www.deutschmann.de/downloads/Support/Profibus/L200.GSD GSD-file for LOCON 200-PB]
* [http://www.deutschmann.de/produkte/download.php?file_id=323 S7-Beispiel-Projekt] (ZIP-Datei)
+
* [https://www.deutschmann.de/downloads/Support/S7/Nockenschaltwerk_CamSwitch/Nsw_v2_e.zip S7-example project] (ZIP-file)
* Handbuch [http://www.deutschmann.de/produkte/download.php?file_id=313 Kommunikationsprofil für Deutschmann Nockensteuerungen] (PDF-Datei)
+
* Manual [https://www.deutschmann.de/downloads/Marketing/Anleitung-Instructions/Handbuecher-Manuals/DIVERS/Kommunikationsprofil/Kommunikationsprofil%20englisch/komm_profil_e.pdf Communication profile for Deutschmann cam controls] (PDF-file)
* Handbuch [http://www.deutschmann.de/produkte/download.php?file_id=319 Nockensteuerungen mit Feldbusanbindung] (PDF-Datei)
+
* Manual [https://www.deutschmann.de/downloads/Marketing/Anleitung-Instructions/Handbuecher-Manuals/Nockenschaltwerke%20-%20Cam%20Controls/NSW%20mit%20Feldbus-CamControlWithFieldbusConnection/English/CamControlsWithFieldbusConnection.pdf Cam controls with fieldbus connection] (PDF-file)

Version vom 27. August 2019, 13:55 Uhr

LOCON 200 and extension module LOCON 200-Out I/O8

Configuration

By factory setting all LOCON 200 cam controls are configured as follows:

  • Outputs: 16
  • Encoder Type: SSI Singleturn
  • Real Encoder resolution: 4096
  • Virtual Encoder resolution: 4096
  • Idle time: Bitwise

This configuration set by default may be changed by using TERM 6 or the software WINLOC 32.

Programming

LOCON 200 can be programmed by TERM 6 or TERM 24 or the software WINLOC 32. The PROFIBUS-Version can be programmed also via PROFIBUS.

Device versions

LOCON 200

LOCON 200 features a serial RS232-interface and a RS485-(DICNET) interface, the needed setting is made through the corresponding rotary coding switches High und Low, located at the bottom side of the device.

Switch Position
High Low Meaning
D DICNET-Adress DICNET-Operation, Bus Termination inactive
E DICNET-Adress DICNET-Operation, Bus Termination active
F F RS232-Operation

Only the DICNET-Addresses 0 ... 15 (decimal) are supported (right rotary coding switch Low = DICNET-Address). Examples:

Switch Position
High Low Meaning
D 3 bus termination inactive, DICNET-Address 3
E C bus termination active, DICNET-Address 12

'Note: The setting via the rotary coding switches is done in hexadecimal.

LOCON 200-PB (PROFIBUS)

LOCON 200-PB (PROFIBUS) is always PROFIBUS-Slave and features a serial RS232-interface and a PROFIBUS-Interface, instead of the RS485-(DICNET) Interface, the needed setting is made through the corresponding rotary coding switches High und Low, located at the bottom side of the device.

Switch Position
High Low Meaning
0 0 PROFIBUS-operation, external address assignment
0 1 PROFIBUS-operation, Adress 1
7 D PROFIBUS-operation, Adress 125
7 E PROFIBUS-operation, external address assignment
F F RS232-operation

Note: The setting via the rotary coding switches is done in hexadecimal.
In LOCON 200-PB two modes are selectable through WINLOC32 via the PROFIBUS-Interface.

The PROFIBUS-Address (Slave-ID) is set on 126 (decimal) in the factory setting. If the rotary coding switch is on position "00" und "7E" then any desired address can be assigned either through WINLOC32 or the PROFIBUS-Master. The GSD-file (L200.GSD) and a S7-example project are available for download on our homepage. Further information regarding LOCON 200-PB can be found in the manual Cam Controls with Fieldbus-Connection.

LOCON 200-MB (Modbus)

LOCON 200-MB (Modbus) is always a Modbus-RTU-Slave and is only available in the 2-core cable-version. LOCON 200-MB features a RS232-Standard-Interface as well as a RS232-(Modbus-RTU) Interface and a RS485-(Modbus-RTU) Interface, which can be changed by adjusting the rotary coding switch High located at the bottom side of the device.

Switch position
High Low Meaning
C x RS232-Modbus (X = ModbusSlave-ID)
D x RS485-Modbus without bus termination (x = Modbus-Slave-ID)
E x RS485-Modbus with activated bus termination (x = Modbus-Slave-ID)
F x RS232-Standard Interface

Note: Only Modbus-Addresses 1 ... 15 (decimal) are supported (right rotary coding switch Low = ID). The Broadcast address 0 is not supported. The Setting via the rotary coding switch is done in hexadecimal.
The following Modbus-RTU-commands are supported by the device:

Modbus-RTU-commands
command meaning
03 (0x03) Read Holding Registers
16 (0x10) Preset Multiple Regs

The transmission baud rate is 19200 Baud; No Parity. Further information regarding LOCON 200-MB can be found in chapter LOCON 200 with Modbus of the Manual for LOCON 200.

LOCON 200-Out I/O8 (extension module)

LOCON 200-Out I/O8 is an extension module and contains 8 I/Os. With this extension module the basic device LOCON 200 resp. (-PB)/(-MB) can be expanded (depending on the version) by 8 I/Os step-by-step to a maximum configuration level of 144 I/Os (incl. the 16 I/Os of LOCON 200 resp. (-PB)/(-MB)). LOCON 200-Out I/O8 contains an own processor. Therefore, the switching accuracy (cycle time) is independent of the LOCON 200(-PB)/(-MB) Basic module.

NT Module for LOCON 200-Out I/O8

The NT module for LOCON 200-Out I/O8 is a power supply that must be used for a configuration level step of more than 8 LOCON 200-Out I/O8 expansion modules. The NT module must be inserted immediately after the LOCON 200 basic unit. Nothing can be connected to the NT module itself. The voltage supply of the NT module takes place via the 24V/DC of the LOCON 200 basic unit. The voltage supply of the then following LOCON 200-Out I/O8 expansion modules is adopted by the NT module

Weblinks