Operating TERM 5, TERM 6, LOCON 16, LOCON 17: Unterschied zwischen den Versionen

Aus Deutschmann Wiki
Zur Navigation springen Zur Suche springen
Zeile 39: Zeile 39:
 
== Initialisation ==
 
== Initialisation ==
 
[[Datei:Kurzbedienungsanleitung Initialisierung.png|thumb|Kurzbedienungsanleitung "Initialisierung"]]
 
[[Datei:Kurzbedienungsanleitung Initialisierung.png|thumb|Kurzbedienungsanleitung "Initialisierung"]]
===Zero-point offset===
+
'''===Zero-point offset===
'''Example:''' Your plant is mechanically already in Position '''0''' . The new encoder is only to be set in the same postion with a lot of work and effort. Via the 4 keys Bedienfront kann in wenigen Schritten einfach und bequem eine Nullpunktverschiebung durchgeführt werden ohne das der Geber mühsam positioniert werden muss.   
+
'''Example:''' Your plant is mechanically already in position '''0''' . The new encoder is only to be set in the same position with a lot of work and effort. Via the 4 keys of the control panel the zero-point offset maybe handled in an easy way in a few steps without positioning the encoder with an effort.   
Nachfolgend wird beispielhaft beschrieben wie eine Nullpunktverschiebung programmiert werden muss. Dabei ist die aktuelle Geberposition (z.B. '''315''') nicht weiter von Bedeutung. <br />
+
Please find here a description how to program a zero-point offset.The actual encoder position (e.g.'''315''') is not of importance. <br />
'''Vorgehensweise:'''
+
'''Procedure:'''
#Die Taste '''-''' muss lang gedrückt werden, bis die '''Zero LED''' leuchtet. Die Anzeige wechselt von der aktuellen Geberposition (z.B. '''315''') auf die Position '''0'''.  
+
#Please press long the key '''-''' until the '''Zero LED''' lights. The value displayed is changing from the actual encoder position (z.B. '''315''') to position '''0'''.  
#Danach muss die Taste '''Enter''' lang gedrückt werden bis die '''Prog.Mode LED''' und die '''Zero LED''' blinken.
+
#Please press now long the key '''Enter''' until '''Prog.Mode LED''' and '''Zero LED''' are flashing.
#Jetzt kann mit den Tasten '''+''' und '''-''' die gewünschte Geberposition (z.B. '''0''') eingestellt werden.  
+
#Now you can program the desired encoder position by using the keys '''+''' and '''-''' (z.B. '''0''').  
#Anschließend wird der Wert mit der Taste '''Enter''' bestätigt und im Nockenschaltwerk gespeichert.
+
#Please confirm this value by pressing the key '''Enter''' , then the programmed value is stored in the cam control.
#In der Anzeige erscheint nun die aktuelle Geberposition '''0'''.
+
#The display shows now the acutal encoder position '''0'''.
  
'''Hinweis:''' Das Beispiel bezieht sich auf eine Nockensteuerung, bei der noch '''keine''' Nullpunktverschiebung programmiert worden ist.
+
'''Note:''' This example is valid only for a cam control where '''no''' zero-Point offset is yet programmed.
  
 
===Drehrichtungsumkehr===
 
===Drehrichtungsumkehr===

Version vom 26. Mai 2014, 13:06 Uhr

Configuration

Parametertabelle

The here described configuration is only valid for cam controls LOCON 90, LOCON 100, LOCON 200, ROTARNOCK 80 and ROTARNOCK 100, which is done by TERM 6. LOCON 16 and LOCON 17 can only be configured by factory.

Reading and changing cam control parameters All cam control parameters that can be reached via the communication profile with GET/SET-PARAMETER can be read and changed via a “menu point“ that is integrated in TERM 6.
Procedure:

  1. Starting from the main menu the keys + und - are pressed long for the same time period.
  2. Thereupon the function LED shines and a 1 (current parameter number) appears on the very right side of the TERM 6 display.
  3. Now this number can by changed by the keys + or - corresponding to the wanted parameter.
  4. Please see parameter table in the corresponding manual. Change of virtual encoder resolution

For instance please find here the change of the virtual encoder resolution.

  1. If the virtual encoder resolution is to be read/changed, please select (see parameter table in the manual communication profile) the corresponding parameter number 19 (corresponds 13H = PNR_SCALED_ENCODER_RES).
  2. Confirm with key Enter and the virtual encoder resolution of the connected cam control is displayed. (e.g. 4096).
  3. If you want to change this value, please press the key Enter again long , until the Prog.Mode LED and the Function LED starts to flash.
  4. Now the value cany be changed with the keys + or - (e.g. 1000).
  5. By pressing again the key Enter the new value is loaded into the cam control.
  6. The value is rejected by pressing the key Esc.

Note The following error messages may appear in case of incorrect use during configuration:

  • E34: change of the parameter not allowed
  • E36: parameter dos not exist
  • E37: Programming of an angle-time-cam larger than Output 16 (Output 8 only ROTARNOCK 80)

The parameter table can be found in the manuals of LOCON 90, LOCON 100, LOCON 200, ROTARNOCK 80 und ROTARNOCK 100. Here for example the parameter table of the manual ROTARNOCK 100.

Programming

Kurzbedienungsanleitung "Programmierung"

Please find here an example how to program via the 4-key control Panel in program 1, output 1 a cam from 100 to 200.
Procedure:

  1. By pressing the key Mode/Esc you can go to the program selection.
  2. With the keys + und - you can choose the wanted program (e.g. Program 1). Please confirm by pressing Enter.
  3. Thereupon you can select by pressing the keys + and - the wanted output(e.g. output 1). This output has to be confirmed by pressing the key Enter.
  4. Please press again the key Enter long until Prog. Mode LED and On LED start flashing.
  5. By using the keys + und - the switch-on-point can be programmed now (e.g. 100). Please confirm by pressing the key Enter.
  6. Now start flashing Prog. Mode LED and Off LED. By using the keys + and - the switch-off-point can be programmed now (z.B. 200). Again please confirm by pressing the key Enter.
  7. By pressing the key Mode/Esc you can leave the programming of the output resp. the otput itself and the selected program ( in this order).

A short manual regarding the programming is to be found in the Manuals of LOCON 7, LOCON 9, LOCON 16, LOCON 17, LOCON 90, LOCON 100, LOCON 200, ROTARNOCK 1, ROTARNOCK 2, ROTARNOCK 3, ROTARNOCK 4, ROTARNOCK 80 und ROTARNOCK 100. Her as an example the short manual-programming for ROTARNOCK 100, originating from the manual of ROTARNOCK 100.

Initialisation

Kurzbedienungsanleitung "Initialisierung"

===Zero-point offset=== Example: Your plant is mechanically already in position 0 . The new encoder is only to be set in the same position with a lot of work and effort. Via the 4 keys of the control panel the zero-point offset maybe handled in an easy way in a few steps without positioning the encoder with an effort. Please find here a description how to program a zero-point offset.The actual encoder position (e.g.315) is not of importance.
Procedure:

  1. Please press long the key - until the Zero LED lights. The value displayed is changing from the actual encoder position (z.B. 315) to position 0.
  2. Please press now long the key Enter until Prog.Mode LED and Zero LED are flashing.
  3. Now you can program the desired encoder position by using the keys + and - (z.B. 0).
  4. Please confirm this value by pressing the key Enter , then the programmed value is stored in the cam control.
  5. The display shows now the acutal encoder position 0.

Note: This example is valid only for a cam control where no zero-Point offset is yet programmed.

Drehrichtungsumkehr

Im Auslieferungszustand haben die Nockensteuerungen die Drehrichtung im Uhrzeigersinn. Nachfolgend wird beschrieben wie eine Drehrichtungsumkehr programmiert werden muss.
Vorgehensweise:

  1. Die Taste + muss lang gedrückt werden, bis die Prog.Mode LED, die Zero LED und die Function LED blinken. In der Anzeige steht nun 0000.
  2. Mit der Taste - kann nun die Drehrichtungsumkehr durchgeführt werden. Im Uhrzeigersinn (0000) und gegen den Uhrzeigersinn (0001).
  3. Mit der Taste Enter muss die Änderung noch bestätigt werden.
  4. Mit der Taste ESC kann die Initialisierung wieder verlassen werden.
  5. Fertig.

Eine Kurzbedienungsanleitung bzgl. der Initialisierung befindet sich in den Handbüchern für das LOCON 7, LOCON 9, LOCON 16, LOCON 17, LOCON 90, LOCON 100, LOCON 200, ROTARNOCK 1, ROTARNOCK 2, ROTARNOCK 3, ROTARNOCK 4, ROTARNOCK 80 und ROTARNOCK 100. Hier beispielhaft die Kurzbedienungsanleitung-Initialisierung aus dem Handbuch für ROTARNOCK 100.

Schnittstellen

Verfügbare Schnittstellen Die Geräte verfügen über eine RS232 und eine RS485 (DICNET) Schnittstelle. Im Auslieferungszustand ist immer die RS485 (DICNET) Schnittstelle eingestellt. Die Schnittstelle ist manuell umschaltbar. An der Geräteunterseite befindet sich ein Aufkleber mit dem Aufdruck Interface. Unter diesem Aufkleber befindet sich ein Schiebeschalter mit dem die Schnittstelle umgeschaltet werden kann.

Weblinks

Handbuch für LOCON 16, LOCON 17 und TERM 6 (PDF-Datei)