UNIGATE® interfaces
(Weitergeleitet von UNIGATE® Schnittstellen/en)
Zur Navigation springen
Zur Suche springen
PC COM-Port
Hereafter follows a description of the PC-COM-Port assignment.
| UNIGATE® | PC COM-Port (9 pol. D-Sub) | |
|---|---|---|
| Assignment | Pin | Assignment |
| Rx / Rx-Debug / DbgRx | 3 | Tx |
| Tx / Tx-Debug / DbgTx | 2 | Rx |
| Appl.-GND / GND / 0V | 5 | GND |
Application Interface(RS232)
Please find hereafter an assignment description for each UNIGATE, which are needed for connection to a PC COM-Port.
| UNIGATE® CL | ||
|---|---|---|
| Plug | Pin | Assignment |
| X1 | 1 | Rx |
| X1 | 2 | Tx |
| X1 | 3 | Appl.-GND |
| Attention: For devices with Option I/O8 information regarding debug via Application Interface is available in the respective manual. | ||
| UNIGATE® CL (Option GT) | ||
| Plug | Pin | Assignment |
| X1 | 1 | Rx |
| X1 | 2 | Tx |
| X1 | 3 | Appl.-GND |
| Attention: For devices with Option I/O8 information regarding debug via Application Interface is available in the respective manual. | ||
| UNIGATE® CM | ||
| Plug | Pin | Assignment |
| X1 | 1 | Rx |
| X1 | 2 | Tx |
| X1 | 3 | Appl.-GND |
| Attention: Information regarding debug via Application Interface is to be found in the manual. | ||
| UNIGATE® EL | ||
| Plug | Pin | Assignment |
| X1 | 1 | Rx |
| X1 | 2 | Tx |
| X1 | 3 | Appl.-GND |
| Attention: Information regarding debug via Application Interface is to be found in the manual. | ||
| UNIGATE® FC | ||
| Plug | Pin | Assignment |
| - | 17 | Rx |
| - | 18 | Tx |
| - | 12 | GND |
| UNIGATE® MB | ||
| Plug | Pin | Assignment |
| X1 | 1 | Rx |
| X1 | 2 | Tx |
| X1 | 3 | Appl.-GND |
| UNIGATE® IC | ||
| Plug | Pin | Assignment |
| - | 29 | Rx |
| - | 30 | Tx |
| - | 24 | GND |
| UNIGATE® RS | ||
| Plug | Pin | Assignement |
| Screw-Plug-Connector 5pol. | 3 | Rx |
| Screw-Plug-Connector 5pol. | 4 | Tx |
| Screw-Plug-Connector 5pol. | 5 | GND |
| Note: Application Interface has to be set by slide switch to RS232. | ||
| UNIGATE® SC | ||
| Plug | Pin | Assignment |
| Screw-Plug-Connector 5pol. | 3 | Rx |
| Screw-Plug-Connector 5pol. | 4 | Tx |
| Screw-Plug-Connector 5pol. | 5 | GND |
| Note: Application Interface has to be set by slide switch to RS232. | ||
| UNIGATE® SC (Option Debug) | ||
| Plug | Pin | Assignment |
| (9 pol. D-Sub) | 2 | Rx |
| (9 pol. D-Sub) | 3 | Tx |
| (9 pol. D-Sub) | 5 | GND |
| Note: Application Interface has to be set by slide switch to RS232. | ||
Debug-Interface
Please find hereafter an assignment description for each UNIGATE, which are needed for connection to a PC COM-Port.
| UNIGATE® CL | ||
|---|---|---|
| Plug | Pin | Assignment |
| X2 | 3 | Rx-Debug |
| X2 | 4 | Tx-Debug |
| X1 | 3 | Appl.-GND |
| Attention: Not in connection with Option I/O8 | ||
| UNIGATE® CL (Option GT) | ||
| Plug | Pin | Assignment |
| X2 | 3 | Rx-Debug |
| X2 | 4 | Tx-Debug |
| X1 | 3 | Appl.-GND |
| Attention: Not in connection with Option I/O8 | ||
| UNIGATE® CX (1. device) | ||
| Plug | Pin | Assignment |
| X1 | 3 | Rx-Debug |
| X1 | 4 | Tx-Debug |
| X1 | 2 | 0V |
| Note: At the communication of the first device the power supply may be connected at plug X2 Pins 1 and 2 of the second device. | ||
| UNIGATE® CX (2. device) | ||
| Plug | Pin | Assignment |
| X2 | 3 | Rx-Debug |
| X2 | 4 | Tx-Debug |
| X2 | 2 | 0V |
| Note: At the communication of the second device the power supply may be connected at plug X1 Pins 1 and 2 of the first device. | ||
| UNIGATE® FC | ||
| Plug | Pin | Assignment |
| - | 16 | DbgRx |
| - | 15 | DbgTx |
| - | 12 | GND |
| UNIGATE® IC | ||
| Plug | Pin | Assignment |
| - | 28 | DbgRx |
| - | 27 | DbgTx |
| - | 24 | GND |
| UNIGATE® SC (Option Debug) | ||
| Plug | Pin | Assignment |
| (9 pol. D-Sub) | 9 | RxD |
| (9 pol. D-Sub) | 4 | TxD |
| (9 pol. D-Sub) | 5 | GND |
| Note: Application Interface has to be set by slide switch to RS232. | ||
