UNIGATE® interfaces: Unterschied zwischen den Versionen
Zur Navigation springen
Zur Suche springen
Reith (Diskussion | Beiträge) |
Reith (Diskussion | Beiträge) |
||
Zeile 140: | Zeile 140: | ||
|} | |} | ||
− | == Debug- | + | == Debug-Interface == |
− | + | Please find hereafter an assignment description for each UNIGATE, which are needed for connection to a PC COM-Port. | |
{| class="wikitable" | {| class="wikitable" | ||
− | |+ | + | |+Connection |
|- | |- | ||
! colspan="3" align="center" | UNIGATE® CL | ! colspan="3" align="center" | UNIGATE® CL | ||
|- | |- | ||
− | ! | + | ! Plug !! Pin !! Assignment |
|- | |- | ||
| X2 || 3 || Rx-Debug | | X2 || 3 || Rx-Debug | ||
Zeile 155: | Zeile 155: | ||
| X1 || 3 || Appl.-GND | | X1 || 3 || Appl.-GND | ||
|- | |- | ||
− | | colspan="3" align="left" | ''' | + | | colspan="3" align="left" | '''Attention:''' Not in connection with Option I/O8 |
|- | |- | ||
! colspan="3" align="center" | UNIGATE® CL (Option GT) | ! colspan="3" align="center" | UNIGATE® CL (Option GT) | ||
|- | |- | ||
− | ! | + | ! Plug !! Pin !! Assignment |
|- | |- | ||
| X2 || 3 || Rx-Debug | | X2 || 3 || Rx-Debug | ||
Zeile 167: | Zeile 167: | ||
| X1 || 3 || Appl.-GND | | X1 || 3 || Appl.-GND | ||
|- | |- | ||
− | | colspan="3" align="left" | ''' | + | | colspan="3" align="left" | '''Attention:''' Not in Connection with Option I/O8 |
|- | |- | ||
− | ! colspan="3" align="center" | UNIGATE® CX (1. | + | ! colspan="3" align="center" | UNIGATE® CX (1. device) |
|- | |- | ||
− | ! | + | ! Plug !! Pin !! Assignment |
|- | |- | ||
| X1 || 3 || Rx-Debug | | X1 || 3 || Rx-Debug | ||
Zeile 179: | Zeile 179: | ||
| X1 || 2 || 0V | | X1 || 2 || 0V | ||
|- | |- | ||
− | | colspan="3" align="left" | ''' | + | | colspan="3" align="left" | '''Note:''' At the communication of the first device the Bei der Kommunikation des 1. Gerätes, kann die Spannungsversorgung am Stecker X2 Pins 1 und 2 des 2. Gerätes angeschlossen werden. |
|- | |- | ||
! colspan="3" align="center" | UNIGATE® CX (2. Gerät) | ! colspan="3" align="center" | UNIGATE® CX (2. Gerät) |
Version vom 11. Mai 2016, 10:13 Uhr
PC COM-Port
Hereafter follows a description of the PC-COM-Port assignment.
UNIGATE® | PC COM-Port (9 pol. D-Sub) | |
---|---|---|
Assignment | Pin | Assignment |
Rx / Rx-Debug / DbgRx | 3 | Tx |
Tx / Tx-Debug / DbgTx | 2 | Rx |
Appl.-GND / GND / 0V | 5 | GND |
Application Interface(RS232)
Please find hereafter an assignment description for each UNIGATE, which are needed for connection to a PC COM-Port.
UNIGATE® CL | ||
---|---|---|
Plug | Pin | Assignment |
X1 | 1 | Rx |
X1 | 2 | Tx |
X1 | 3 | Appl.-GND |
Attention: For devices with Option I/O8 information regarding debug via Application Interface is available in the respective manual. | ||
UNIGATE® CL (Option GT) | ||
Plug | Pin | Assignment |
X1 | 1 | Rx |
X1 | 2 | Tx |
X1 | 3 | Appl.-GND |
Attention: For devices with Option I/O8 information regarding debug via Application Interface is available in the respective manual. | ||
UNIGATE® CM | ||
Plug | Pin | Assignment |
X1 | 1 | Rx |
X1 | 2 | Tx |
X1 | 3 | Appl.-GND |
Attention: Information regarding debug via Application Interface is to be found in the manual. | ||
UNIGATE® EL | ||
Plug | Pin | Assignment |
X1 | 1 | Rx |
X1 | 2 | Tx |
X1 | 3 | Appl.-GND |
Attention: Information regarding debug via Application Interface is to be found in the manual. | ||
UNIGATE® FC | ||
Plug | Pin | Assignment |
- | 17 | Rx |
- | 18 | Tx |
- | 12 | GND |
UNIGATE® MB | ||
Plug | Pin | Assignment |
X1 | 1 | Rx |
X1 | 2 | Tx |
X1 | 3 | Appl.-GND |
UNIGATE® IC | ||
Plug | Pin | Assignment |
- | 29 | Rx |
- | 30 | Tx |
- | 24 | GND |
UNIGATE® RS | ||
Plug | Pin | Assignement |
Screw-Plug-Connector 5pol. | 3 | Rx |
Screw-Plug-Connector 5pol. | 4 | Tx |
Screw-Plug-Connector 5pol. | 5 | GND |
Note: Application Interface has to be set by slide switch to RS232. | ||
UNIGATE® SC | ||
Plug | Pin | Assignment |
Screw-Plug-Connector 5pol. | 3 | Rx |
Screw-Plug-Connector 5pol. | 4 | Tx |
Screw-Plug-Connector 5pol. | 5 | GND |
Note: Application Interface has to be set by slide switch to RS232. | ||
UNIGATE® SC (Option Debug) | ||
Plug | Pin | Assignment |
(9 pol. D-Sub) | 2 | Rx |
(9 pol. D-Sub) | 3 | Tx |
(9 pol. D-Sub) | 5 | GND |
Note: Application Interface has to be set by slide switch to RS232. |
Debug-Interface
Please find hereafter an assignment description for each UNIGATE, which are needed for connection to a PC COM-Port.
UNIGATE® CL | ||
---|---|---|
Plug | Pin | Assignment |
X2 | 3 | Rx-Debug |
X2 | 4 | Tx-Debug |
X1 | 3 | Appl.-GND |
Attention: Not in connection with Option I/O8 | ||
UNIGATE® CL (Option GT) | ||
Plug | Pin | Assignment |
X2 | 3 | Rx-Debug |
X2 | 4 | Tx-Debug |
X1 | 3 | Appl.-GND |
Attention: Not in Connection with Option I/O8 | ||
UNIGATE® CX (1. device) | ||
Plug | Pin | Assignment |
X1 | 3 | Rx-Debug |
X1 | 4 | Tx-Debug |
X1 | 2 | 0V |
Note: At the communication of the first device the Bei der Kommunikation des 1. Gerätes, kann die Spannungsversorgung am Stecker X2 Pins 1 und 2 des 2. Gerätes angeschlossen werden. | ||
UNIGATE® CX (2. Gerät) | ||
Stecker | Pin | Belegung |
X2 | 3 | Rx-Debug |
X2 | 4 | Tx-Debug |
X2 | 2 | 0V |
Hinweis: Bei der Kommunikation des 2. Gerätes, kann die Spannungsversorgung am Stecker X1 Pins 1 und 2 des 1. Gerätes angeschlossen werden. | ||
UNIGATE® FC | ||
Stecker | Pin | Belegung |
- | 16 | DbgRx |
- | 15 | DbgTx |
- | 12 | GND |
UNIGATE® IC | ||
Stecker | Pin | Belegung |
- | 28 | DbgRx |
- | 27 | DbgTx |
- | 24 | GND |
UNIGATE® SC (Option Debug) | ||
Stecker | Pin | Belegung |
(9 pol. D-Sub) | 9 | RxD |
(9 pol. D-Sub) | 4 | TxD |
(9 pol. D-Sub) | 5 | GND |
Hinweis: Die Applikationsschnittstelle muss über den Schiebeschalter auf RS232 eingestellt werden. |