UNIGATE® interfaces

Aus Deutschmann Wiki
Zur Navigation springen Zur Suche springen

PC COM-Port

Hereafter follows a description of the PC-COM-Port assignment.

Connection
UNIGATE® PC COM-Port (9 pol. D-Sub)
Assignment Pin Assignment
Rx / Rx-Debug / DbgRx 3 Tx
Tx / Tx-Debug / DbgTx 2 Rx
Appl.-GND / GND / 0V 5 GND

Application Interface(RS232)

Please find hereafter an assignment description for each UNIGATE, which are needed for a connection to a PC COM-Port.

Connection
UNIGATE® CL
Plug Pin Assignment
X1 1 Rx
X1 2 Tx
X1 3 Appl.-GND
Attention: For devices with Option I/O8 Information regarding debug via Application Interface is available in the respective manual.
UNIGATE® CL (Option GT)
Stecker Pin Belegung
X1 1 Rx
X1 2 Tx
X1 3 Appl.-GND
Attention: For devices with Option I/O8 Information regarding debug via Application Interface is available in the respective manual.
UNIGATE® CM
Plug Pin Assignment
X1 1 Rx
X1 2 Tx
X1 3 Appl.-GND
Achtung: Die Informationen zum Debuggen über die Applikationsschnittstelle sind dem Handbuch zu entnehmen.
UNIGATE® EL
Stecker Pin Belegung
X1 1 Rx
X1 2 Tx
X1 3 Appl.-GND
Achtung: Die Informationen zum Debuggen über die Applikationsschnittstelle sind dem Handbuch zu entnehmen.
UNIGATE® FC
Stecker Pin Belegung
- 17 Rx
- 18 Tx
- 12 GND
UNIGATE® MB
Stecker Pin Belegung
X1 1 Rx
X1 2 Tx
X1 3 Appl.-GND
UNIGATE® IC
Stecker Pin Belegung
- 29 Rx
- 30 Tx
- 24 GND
UNIGATE® RS
Stecker Pin Belegung
5pol. Schraub-Steckverbinder 3 Rx
5pol. Schraub-Steckverbinder 4 Tx
5pol. Schraub-Steckverbinder 5 GND
Hinweis: Die Applikationsschnittstelle muss über den Schiebeschalter auf RS232 eingestellt werden.
UNIGATE® SC
Stecker Pin Belegung
5pol. Schraub-Steckverbinder 3 Rx
5pol. Schraub-Steckverbinder 4 Tx
5pol. Schraub-Steckverbinder 5 GND
Hinweis: Die Applikationsschnittstelle muss über den Schiebeschalter auf RS232 eingestellt werden.
UNIGATE® SC (Option Debug)
Stecker Pin Belegung
(9 pol. D-Sub) 2 Rx
(9 pol. D-Sub) 3 Tx
(9 pol. D-Sub) 5 GND
Hinweis: Die Applikationsschnittstelle muss über den Schiebeschalter auf RS232 eingestellt werden.

Debug-Schnittstelle

Nachfolgend wird die Belegung des jeweiligen UNIGATEs beschrieben, die für eine Verbindung zu einem PC COM-Port benötigt werden.

Anschluss
UNIGATE® CL
Stecker Pin Belegung
X2 3 Rx-Debug
X2 4 Tx-Debug
X1 3 Appl.-GND
Achtung: Nicht in Verbindung mit Option I/O8
UNIGATE® CL (Option GT)
Stecker Pin Belegung
X2 3 Rx-Debug
X2 4 Tx-Debug
X1 3 Appl.-GND
Achtung: Nicht in Verbindung mit Option I/O8
UNIGATE® CX (1. Gerät)
Stecker Pin Belegung
X1 3 Rx-Debug
X1 4 Tx-Debug
X1 2 0V
Hinweis: Bei der Kommunikation des 1. Gerätes, kann die Spannungsversorgung am Stecker X2 Pins 1 und 2 des 2. Gerätes angeschlossen werden.
UNIGATE® CX (2. Gerät)
Stecker Pin Belegung
X2 3 Rx-Debug
X2 4 Tx-Debug
X2 2 0V
Hinweis: Bei der Kommunikation des 2. Gerätes, kann die Spannungsversorgung am Stecker X1 Pins 1 und 2 des 1. Gerätes angeschlossen werden.
UNIGATE® FC
Stecker Pin Belegung
- 16 DbgRx
- 15 DbgTx
- 12 GND
UNIGATE® IC
Stecker Pin Belegung
- 28 DbgRx
- 27 DbgTx
- 24 GND
UNIGATE® SC (Option Debug)
Stecker Pin Belegung
(9 pol. D-Sub) 9 RxD
(9 pol. D-Sub) 4 TxD
(9 pol. D-Sub) 5 GND
Hinweis: Die Applikationsschnittstelle muss über den Schiebeschalter auf RS232 eingestellt werden.