Changing or Replacing UNIGATE® RS by UNIGATE® CL

The table below describes which points need to be observed when changing or replacing UNIGATE® RS by UNIGATE® CL. In addition to information on hardware and software, we have included also information on EPLAN files in order to possibly adapt the documentation accordingly.

	UNIGATE® RS		UNIGATE® CL		Note
					UNIGATE® CL: UNIGATE® CL is available in housing colours Blue und Grey. Attention: OEM-devices may vary in colour.
Protocol			(*see note)		UNIGATE® CL: Universalscript Deutschmann is loaded by state of delivery. This script is containing all protocols available in UNIGATE® RS. By using the configuration software WINGATE the needed protocol can be chosen and UNIGATE® CL may be configured and used as UNIGATE® RS.
Script
Software
configuration software WINGATE					UNIGATE® CL: Configuration file (*.gwc) of UNIGATE® RS can not be loaded into UNIGATE® CL.
Mechanics
Housing WxHxD	90 x 127 x 55 mm		23 x 111 x 117 mm		The measurements for H and D may slightly differ depending on the version. Detailed information is to be found in the corresponding manual.
Protection type	IP24		IP20
Connection-Power Supply	Mounting Position
	Frontal-Bottom		Bottom
	Screw-Plug-Connector 5 pol.	Screw-Plug-Connector 2 pol. (for 9 pol. D-Sub Plug-Connector)	Screw-Plug-Connector X2
Power Supply	Screw-Plug-Connector 5 pol.	Screw-Plug-Connector 2 pol. (for 9 pol. D-Sub Plug-Connector)	Screw-Plug-Connector 4 pol. X2
+24V/DC	Pin 1	Pin 1	Pin 1
0V (GND)	Pin 2	Pin 2	Pin 2
Housing-Earthing	Earthing Clamp via DIN-Rail		Earthing Clamp via DIN-Rail
	UNIGATE RS (Housing-Earthing)		UNIGATE CL (Housing-Earthing)		UNIGATE® RS: At elder devices the earthing is done by flat plug connectors. Example shows UNIGATE RS232&485-CO
Connection Serial	Mounting Position
	Frontal-Bottom		Top	Bottom
	Screw-Plug-Connector 5 pol.	9 pol. D-Sub Plug-Connector	Screw-Plug-Connector X1	Screw-Plug-Connector X2
Application Interface (RS232)	Screw-Plug-Connector 5 pol.	9 pol. D-Sub Plug-Connector	Screw-Plug-Connector 3 pol. X1
Rx	Pin 3	Pin 2	Pin 1
Tx	Pin 4	Pin 3	Pin 2
AP-GND	Pin 5	Pin 5	Pin 3
Application Interface (RS485)	Screw-Plug-Connector 5 pol.	9 pol. D-Sub Plug-Connector	Screw-Plug-Connector 4 pol. X1
RS485 (+)	Pin 4	Pin 3	connect Pin 4 with Pin 6
RS485 (-)	Pin 3	Pin 2	connect Pin 5 with Pin 7
Application Interface (RS422)	Screw-Plug Connector 5 pol.	9 pol. D-Sub Plug-Connector	Screw-Plug Connector 4 pol. X1
Rx422 (+)		Pin 7	Pin 4
Rx422 (-)		Pin 6	Pin 5
Tx422 (+)		Pin 3	Pin 6
Tx422 (-)		Pin 2	Pin 7
Debug-Interface	Screw-Plug-Connector 5 pol.	9 pol. D-Sub Plug-Connector		Screw-Plug-Connector 4 pol. X2
Rx-Debug				Pin 3
Tx-Debug				Pin 4
Selection Application Interface	to be selected by slide switch		configurable
RS232					UNIGATE® RS: Depending on the device version, a switching by slide switch is only possible between RS232 and RS485 or RS232 and RS422. UNIGATE® CL: The needed application interface may be configured by configuration software WINGATE (only in combination with Universalscript Deutschmann). Attention: If RS485 is used, then external wirebridges are mandatory. (see pin assignment Plug X1). Configuration Application-Interface
RS485
RS422
Termination
RS422 (Tx)	Connectible by slide switch		Connectible by slide switch below X1		UNIGATE® CL: 2 slide switches for termination are located below X1. Slide Switches Termination Application-Interface
RS422 (Rx)	set fixed		Connectible by slide switch below X1
RS485	Connectible by slide switch		Connectible by one slide switch below X1		UNIGATE® CL: Only slide switch Tx422 has to be set to position ON. Slide switch Rx422 has to be set to position OFF.
Application Interface Rotary Coding Switches & LEDs	Mounting Position			Application Interface Rotary Coding Switches & LEDs
	Frontal-Bottom		Frontal
	Application- Interface Rotary Coding Switches & LEDs		Application- Interface Rotary Coding Switches & LEDs
Rotary Coding Switch S4				Rotary Coding Switch S4	UNIGATE® CL: Operating modes may be selected correspondingly as at UNIGATE® RS. Attention: Switch position "DD" is reserved for internal use and is not allowed to use.
Rotary Coding Switch S5				Rotary Coding Switch S5
LED Power				LED Power
LED State				LED State
LED Error No / Select ID				LEDs 1/2/4/8 (Error No / Select ID)
Connection Fieldbus	Mounting Position
	Frontal-Top		Frontal	Bottom
CANopen	Connection via 9 pol. D-Sub Plug-Connector		Connection via 9 pol. D-Sub Plug-Connector
DeviceNet	Connection via Screw-Plug-Connector 5 pol.			Connection via Screw-Plug-Connector 5 pol.
Ethernet	Connection via RJ 45 Socket			Connection via RJ 45 Socket
MPI	Connection via 9 pol. D-Sub-Socket		Connection via 9 pol. D-Sub-Socket
PROFIBUS	Connection via 9 pol. D-Sub-Socket		Connection via 9 pol. D-Sub-Socket
Termination	Connectible by slide switch		Connectible by slide switch		UNIGATE® CL: Exception Ethernet. UNIGATE® RS: Exception Ethernet.
Fieldbus Rotary Coding Switches/Dip-switch/LEDs	Mounting Position			Fieldbus Rotary Coding Switches/Dip-switch/LEDs
	Frontal-Top		Frontal
CANopen	Fieldbus Dip-Switch & LEDs		Fieldbus Dip-Switch & LEDs	CANopen
Dip-Switch				Dip-Switch
LED BUS Power				LED BUS Power
LED BUS State				LED BUS State
DeviceNet	Fieldbus Dip-Switch & LEDs		Fieldbus Dip-Switch & LEDs	DeviceNet
Dip-Switch				Dip-Switch
LED BUS Power				LED BUS Power
LED BUS State (MNS)				LED BUS State
Ethernet	Ethernet LEDs		Ethernet LEDs	Ethernet
LED Link				LED Link/Act.	UNIGATE® CL: LED Link/Act. serves to display both LEDs "Link" und "LAN".
LED LAN
LED Bus State				LED (Ethernet) State
				LED (Ethernet) Power
				LED Full Duplex
				LED 100 MB
MPI	Fieldbus Rotary Coding Switches & LEDs		Fieldbus Rotary Coding Switches & LEDs	MPI
Rotary Coding Switch High				Rotary Coding Switch High
Rotary Coding Switch LOW				Rotary Coding Switch LOW
LED BUS Power				LED BUS Power
LED BUS Control				LED BUS
LED BUS State				LED BUS State
PROFIBUS	Fieldbus Rotary Coding Switches & LEDs		Fieldbus Rotary Coding Switches & LEDs	PROFIBUS
Rotary Coding Switch High				Rotary Coding Switch High
Rotary Coding Switch LOW				Rotary Coding Switch LOW
LED BUS Power				LED BUS Power
LED BUS Error				LED BUS
LED BUS State				LED BUS State
Device Description Files
CANopen	DAGW2298.eds				UNIGATE® CL: The device description file of UNIGATE® RS possibly has to be adapted for UNIGATE® CL.
	DAGW2317.eds
DeviceNet	DAGW2242.eds				UNIGATE® CL: The device description file of UNIGATE® RS possibly has to be adapted for UNIGATE® CL.
	DAGW2299.eds
	DAGW2853.eds
	DAGW2857.eds
Ethernet					Not needed.
MPI					Not needed.
PROFIBUS DPV0	DAGW2079.gsd		DAGW2079.gsd		UNIGATE® CL: Via configuration software WINGATE may be set the Ident Number to "2079". With this setting the old GSD-file can be kept and the project needs not to be changed.
PROFIBUS DPV1	UGIC3218.gsd		UGIC3218.gsd
EPLAN
CANopen					UNIGATE® CL: Makro for EPLAN may be downloaded from our homepage. EPLAN - Macro Unigate CL-C4 (Macro-File) Description Makros UNIGATE® CL (PDF-File)
DeviceNet					UNIGATE® CL: Makro for EPLAN may be downloaded from our homepage. EPLAN - Macro Unigate CL-DN (Macro-File) Description Makros UNIGATE® CL (PDF-File)
Ethernet					UNIGATE® CL: Makro for EPLAN may be downloaded from our homepage. EPLAN - Macro Unigate CL-FE (Macro-File) Description Makros UNIGATE® CL (PDF-File)
MPI					UNIGATE® CL: Makro for EPLAN may be downloaded from our homepage. EPLAN - Macro Unigate CL-MPI (Macro-File) Description Makros UNIGATE® CL (PDF-File)
PROFIBUS					UNIGATE® CL: Makro for EPLAN may be downloaded from our homepage. EPLAN - Macro Unigate CL-PB (Macro-File) Description Makros UNIGATE® CL (PDF-File)

= available
= not available
Further detailed information may be found in the corresponding manual in chapter "Technical Data".