2.226
Bearbeitungen
Änderungen
Zur Navigation springen
Zur Suche springen
→Weblinks
[[Datei:WINGATE.jpg|thumb|Konfigurationssoftware WINGATE]]
The software WINGATE [[#Weblinks|''WINGATE®'']] is a configuration software for Deutschmann UNIGATE®-devices. A detailed description of the functions listed below can be found in [[#Weblinks|''Manual for WINGATE®'']].
== Device Configuration ==
The device configuration maybe done via ''Application Interface (RS232)'' or via ''Debug-Interface''.
#At the first start will open a '''"dialog window"''' showing the note that the acutal selected COM-Port does not exist. Please confirm this dialog window with '''"OK"'''.
#Via the menue item '''"Options"'''→'''"Port"''' select the used COM-Port. If there exists no real COM-Port at the PC, an [[USB-to-RS232 converter]] is needed.
#After that the UNIGATE® has to be connected via [[UNIGATE® interfaces|'''Application Interface (RS232)''']] and to be started in '''Configuration Mode''' (Rotary switches '''S4 + S5''' set to '''"FF"'''). WINGATE will show the startup message of the UNIGATE®.
#Via the menue item '''"File"'''→'''"Upload"''' the configuration of UNIGATE® can be read now.
#Via the menue items '''"more items visible"''' und '''"more items editable"''' more parameters (if available) are shown and maybe changed.
#At the first start will open a '''"dialog window"''' showing the note that the acutal selected COM-Port does not exist. Please confirm this dialog window with '''"OK"'''.
#Via the menue item '''"Options"'''→'''"Port"''' select the used COM-Port. If there exists no real COM-Port at the PC, an [[USB-to-RS232 converter]] is needed.
#Danach muss das After that the UNIGATE® über die has to be connected via [[UNIGATE® Schnittstelleninterfaces|'''Debug-SchnittstelleInterface''']] angeschlossen und im and to be started in '''DatenaustauschmodusData Exchange Mode''' (Drehkodierschalter Rotary switches '''S4 + S5''' z.B. auf set to '''"00"''') gestartet werden. In der Statusleiste erscheint die Meldung the status bar will appear the message '''"Device started in WINGATE-Mode"'''.#Then start Via the menue item '''"Extras"'''→'''"Upload_Config_Debug"''' the configuration of the UNIGATE® can be read. A '''"dialog window'''" will show up with the note: '''"Restart UNIGATE in Run-Mode and confirm"'''. Before to be able to confirm this '''"dialog window"'Data Exchange Mode'' with '''"OK"''', UNIGATE® has to be started again. In Only when in the status bar the message will appear the message '''"Device started starting in WINGATE-Mode"''' , this '''"Dialog Window"''' maybe confirmed with '''"OK"'''.#Via Now the upload will be processed. During this process the menue item message '''"ExtrasUpload"'''→will be shown in the status bar. After a successfull upload will appear the message '''"Upload_Config_DebugUpload finished"''' in the configuration of the UNIGATE® can be readStatus bar.
#Via the menue items '''"more items visible"''' und '''"more items editable"''' more parameters (if available) are shown and maybe changed.
#Via the menue item ''''"Extras"'''→'''"Download_Config_Debug"''' the changed configuration now can be loaded into the UNIGATE®. A '''"dialog window'''" will show up with the note: '''"Restart UNIGATE in Run-Mode and confirm"'''. Before to be able to confirm this '''"dialog window"''' with '''"OK"''', UNIGATE® has to be started again. Only when in the status bar the message will appear '''"Device starting in WINGATE-Mode"''' , this '''"Dialog Window"''' maybe confirmed with '''"OK"'''. Now the download will be processed. During this process the message '''"Downloading..."''' will be shown in the status bar. After a successfull upload will appear the message '''"Download finished"''' in the status bar.
#Via the menue item '''"File"'''→'''"Save as"''' the configuration of the UNIGATE® can be saved and filed.
#Done.
== Script loading via Application Interface (RS 232) ==
#Install WINGATE and start.
#At the first start will open a '''"dialog window"''' showing the note that the acutal selected COM-Port does not exist. Please confirm this dialog window with '''"OK"'''.
#Via the menue item '''"Options"'''→'''"Port"''' select the used COM-Port. If there exists no real COM-Port at the PC, an [[USB-to-RS232 converter]] is needed.
#After that the UNIGATE® has to be connected via [[UNIGATE® interfaces|'''Application Interface (RS232)''']] and to be started in '''Configuration Mode'''. WINGATE will show the startup message of the UNIGATE®.
#Then start the UNIGATE® in '''Configuration-Mode'''. WINGATE will show the startup message of the UNIGATE®.
#Via the menue item '''"File"'''→'''"Write Script"''' the needed script (*.dcs) can be selected and is loaded thereafter directly into the UNIGATE®.
#After that the UNIGATE® will start automatically new and displays a new startup message.
#Done.
== Loading Firmware Script Extension ==
#Install WINGATE® and start.
#At the first start will open a '''"dialog window"''' showing the note that the acutal selected COM-Port does not exist. Please confirm this dialog window with '''"OK"'''.
#Via the menue item '''"Options"'''→'''"Port"''' select the used COM-Port. If there exists no real COM-Port at the PC, an [[USB-to-RS232 converter]] is needed.
#After that the UNIGATE® has to be connected via [[UNIGATE® interfaces|'''Application Interface (RS232)''']] and to be started in '''Configuration Mode''' (Rotary switches '''S4 + S5''' set to '''"FF"'''). WINGATE will show the startup message of the UNIGATE®.
#Via the menue item '''"Extras"'''→'''"Firmware script extension"''' can be selected the corresponding Firmware Script Extension. The window ''Extension Dlg'' will show up where the selected Firmware Script Extension is checked.
#If the message '''"File read without errors"''' appears the Firmware script extension can be loaded into the UNIGATE® via the button '''write extension'''.
#After that a further window has to be closed by the button '''OK''' and afterwards the window ''Extension Dlg'' has to be closed via the button '''close'''.
== Create device description file ==
Device description files can be created with WINGATE®. The compulsory requirement is that the „Universalscript Deutschmann“ is loaded in the UNIGATE®. '''Note:''' 'The device description file created with WINGATE® can also be used for UNIGATE® devices, in which a customer-specific script is subsequently loaded. Requirement here is that only the fieldbus input data length and the fieldbus output data length are configured. In addition the „Product-Code“ in the device description file has to be compared with the article no. (Vxxx) of the UNIGATE® used. These must be identical.
#Install WINGATE® and start.
#At the first start will open a '''"dialog window"''' showing the note that the acutal selected COM-Port does not exist. Please confirm this dialog window with '''"OK"'''.
#Via the menue item '''"Options"'''→'''"Port"''' select the used COM-Port. If there exists no real COM-Port at the PC, an [[USB-to-RS232 converter]] is needed.
#After that the UNIGATE® has to be connected via [[UNIGATE® interfaces|'''Application Interface (RS232)''']] and to be started in '''Configuration Mode''' (Rotary switches '''S4 + S5''' set to '''"FF"'''). WINGATE will show the startup message of the UNIGATE®.
#Via the menue item '''"Extras"'''→'''"Upload"''' the configuration of the UNIGATE® can be read.
#Via the menue items '''"more items visible"''' und '''"more items editable"''' more parameters (if available) are shown and maybe changed.
#The data lengths of the fieldbus input and the fieldbus output must then be determined. The length must be entered via the parameters '''"Blocklength fieldbus input"''' and ''"Blocklength fieldbus output"'''.
#Via the menue item '''"Options"'''→'''"Generate... File"''' can be created a device description file.
#Via the menue item '''"File"'''→'''"Download"''' can now be loaded the changed configuration in the UNIGATE®. '''Note:''' The created device description file has to match with the device configuration of the UNIGATE®.
== Reset Device ==
#At the first start will open a '''"dialog window"''' showing the note that the acutal selected COM-Port does not exist. Please confirm this dialog window with '''"OK"'''.
#Via the menue item '''"Options"'''→'''"Port"''' select the used COM-Port. If there exists no real COM-Port at the PC, an [[USB-to-RS232 converter]] is needed.
#After that the UNIGATE® has to be connected via [[UNIGATE® interfaces|'''Application Interface (RS232)''']] and to be started in '''Configuration Mode''' (Rotary switches '''S4 + S5''' set to '''"FF"'''). WINGATE will show the startup message of the UNIGATE®.
#Then start the UNIGATE® in '''Configuration-Mode'''. WINGATE will show the startup message of the UNIGATE®.
#Via the menue item '''"Options"'''→'''"Reset Device"''' the reset can be carried out now.
== Weblinks ==
*[httphttps://www.deutschmann.de/produktedownloads/downloadSoftware/Wingate/SetupGW.php?file_id=577 zip Software WINGATE] (Zip-DateiZIP file)*[httphttps://www.deutschmann.de/produktedownloads/Marketing/Anleitung-Instructions/Handbuecher-Manuals/Softwaretools/downloadEnglisch/WINGATE/WINGATE_e.php?file_id=678 Handbuch für pdf Manual for WINGATE] (PDF-Dateifile)
