WINGATE

Aus Deutschmann Wiki
Version vom 12. Januar 2022, 09:00 Uhr von Biegel (Diskussion | Beiträge) (→‎Weblinks)
(Unterschied) ← Nächstältere Version | Aktuelle Version (Unterschied) | Nächstjüngere Version → (Unterschied)
Zur Navigation springen Zur Suche springen
Configuration software WINGATE

The software WINGATE® is a configuration software for Deutschmann UNIGATE®-devices. A detailed description of the functions listed below can be found in Manual for WINGATE®.

Device Configuration

The device configuration maybe done via Application Interface (RS232) or via Debug-Interface.

Application Interface (RS232)

  1. Install WINGATE and start.
  2. At the first start will open a "dialog window" showing the note that the acutal selected COM-Port does not exist. Please confirm this dialog window with "OK".
  3. Via the menue item "Options""Port" select the used COM-Port. If there exists no real COM-Port at the PC, an USB-to-RS232 converter is needed.
  4. After that the UNIGATE® has to be connected via Application Interface (RS232) and to be started in Configuration Mode (Rotary switches S4 + S5 set to "FF"). WINGATE will show the startup message of the UNIGATE®.
  5. Via the menue item "File""Upload (read from device)" the configuration of UNIGATE® can be read now.
  6. Via the menue items "more items visible" und "more items editable" more parameters (if available) are shown and maybe changed.
  7. Via the menue item "File""Download (write to device)" the changed configuration now can be loaded into the UNIGATE®.
  8. Via the menue item "File""Save as" the configuration of UNIGATE® can be saved and filed.
  9. Done.

Debug Interface

  1. Install WINGATE and start.
  2. At the first start will open a "dialog window" showing the note that the acutal selected COM-Port does not exist. Please confirm this dialog window with "OK".
  3. Via the menue item "Options""Port" select the used COM-Port. If there exists no real COM-Port at the PC, an USB-to-RS232 converter is needed.
  4. After that the UNIGATE® has to be connected via Debug Interface and to be started in Data Exchange Mode (Rotary switches S4 + S5 set to "00").In the status bar will appear the message "Device started in WINGATE-Mode".
  5. Via the menue item "Extras""Upload (read from device) via debug port" the configuration of the UNIGATE® can be read. A "dialog window" will show up with the note: "Restart UNIGATE in Run-Mode and confirm". Before to be able to confirm this "dialog window" with "OK", UNIGATE® has to be started again. Only when in the status bar the message will appear "Device starting in WINGATE-Mode" , this "Dialog Window" maybe confirmed with "OK". Now the upload will be processed. During this process the message "Upload" will be shown in the status bar. After a successfull upload will appear the message "Upload finished" in the Status bar.
  6. Via the menue items "more items visible" und "more items editable" more parameters (if available) are shown and maybe changed.
  7. Via the menue item '"Extras""Download (write to device) via debug port" the changed configuration now can be loaded into the UNIGATE®. A "dialog window" will show up with the note: "Restart UNIGATE in Run-Mode and confirm". Before to be able to confirm this "dialog window" with "OK", UNIGATE® has to be started again. Only when in the status bar the message will appear "Device starting in WINGATE-Mode" , this "Dialog Window" maybe confirmed with "OK". Now the download will be processed. During this process the message "Downloading..." will be shown in the status bar. After a successfull upload will appear the message "Download finished" in the status bar.
  8. Via the menue item "File""Save as" the configuration of the UNIGATE® can be saved and filed.
  9. Done.

Script loading

  1. Install WINGATE and start.
  2. At the first start will open a "dialog window" showing the note that the acutal selected COM-Port does not exist. Please confirm this dialog window with "OK".
  3. Via the menue item "Options""Port" select the used COM-Port. If there exists no real COM-Port at the PC, an USB-to-RS232 converter is needed.
  4. After that the UNIGATE® has to be connected via Application Interface (RS232) and to be started in Configuration Mode. WINGATE will show the startup message of the UNIGATE®.
  5. Then start the UNIGATE® in Configuration-Mode. WINGATE will show the startup message of the UNIGATE®.
  6. Via the menue item "File""Write Script" the needed script (*.dcs) can be selected and is loaded thereafter directly into the UNIGATE®.
  7. This process may take some time.
  8. When the process is finished, a confirmation dialog is shown.

Loading Firmware Script Extension

  1. Install WINGATE® and start.
  2. At the first start will open a "dialog window" showing the note that the acutal selected COM-Port does not exist. Please confirm this dialog window with "OK".
  3. Via the menue item "Options""Port" select the used COM-Port. If there exists no real COM-Port at the PC, an USB-to-RS232 converter is needed.
  4. After that the UNIGATE® has to be connected via Application Interface (RS232) and to be started in Configuration Mode (Rotary switches S4 + S5 set to "FF"). WINGATE will show the startup message of the UNIGATE®.
  5. Via the menue item "Extras""Firmware script extension" can be selected the corresponding Firmware Script Extension. The window Extension Dlg will show up where the selected Firmware Script Extension is checked.
  6. If the message "File read without errors" appears the Firmware script extension can be loaded into the UNIGATE® via the button write extension.
  7. After that a further window has to be closed by the button OK and afterwards the window Extension Dlg has to be closed via the button close.

Generate a sample device description file

A sample device description files can be created with WINGATE®. The compulsory requirement is that the „Universalscript Deutschmann“ is loaded in the UNIGATE®. Note: 'The sample device description file created with WINGATE® can also be used for UNIGATE® devices, in which a customer-specific script is subsequently loaded. Requirement here is that only the fieldbus input data length and the fieldbus output data length are configured. In addition the „Product-Code“ in the device description file has to be compared with the article no. (Vxxx) of the UNIGATE® used. These must be identical.

  1. Install WINGATE® and start.
  2. At the first start will open a "dialog window" showing the note that the acutal selected COM-Port does not exist. Please confirm this dialog window with "OK".
  3. Via the menue item "Options""Port" select the used COM-Port. If there exists no real COM-Port at the PC, an USB-to-RS232 converter is needed.
  4. After that the UNIGATE® has to be connected via Application Interface (RS232) and to be started in Configuration Mode (Rotary switches S4 + S5 set to "FF"). WINGATE will show the startup message of the UNIGATE®.
  5. Via the menue item "Extras""Upload (read from device)" the configuration of the UNIGATE® can be read.
  6. Via the menue items "more items visible" und "more items editable" more parameters (if available) are shown and maybe changed.
  7. The data lengths of the fieldbus input and the fieldbus output must then be determined. The length must be entered via the parameters "Blocklength fieldbus input"' and "Blocklength fieldbus output".
  8. Via the menue item "Options""Generate a sample device description file" can be created a sample device description file.
  9. Via the menue item "File""Download (write to device)" can now be loaded the changed configuration in the UNIGATE®. Note: The created sample device description file has to match with the device configuration of the UNIGATE®.

Reset Device

  1. Install WINGATE and start.
  2. At the first start will open a "dialog window" showing the note that the acutal selected COM-Port does not exist. Please confirm this dialog window with "OK".
  3. Via the menue item "Options""Port" select the used COM-Port. If there exists no real COM-Port at the PC, an USB-to-RS232 converter is needed.
  4. After that the UNIGATE® has to be connected via Application Interface (RS232) and to be started in Configuration Mode (Rotary switches S4 + S5 set to "FF"). WINGATE will show the startup message of the UNIGATE®.
  5. Then start the UNIGATE® in Configuration-Mode. WINGATE will show the startup message of the UNIGATE®.
  6. Via the menue item "Options""Reset Device" the reset can be carried out now.
  7. The then opening dialog window should be confirmed with "Ja" only if the "Reset Device" really should be carried out. The loaded script will be deleted. Note for UNIGATE® CL: From version V2.64 the Universalscript Deutschmann will remain on the device, if this was loaded to it before "Reset Device"is executed.
  8. This process may take some time.
  9. When the process is finished, a confirmation dialog is shown.

Weblinks