Changing or Replacing UNIGATE® CO(M)-ProfibusDP by UNIGATE® CX-C4Map-PBDPV1

The table below describes which points need to be observed when changing or replacing UNIGATE® CO(M)-ProfibusDP by UNIGATE® CX-C4Map-PBDPV1. In addition to the information on the hardware and software, this also contains information on the EPLAN files so that the documentation can be adapted accordingly if necessary.


	UNIGATE® CO(M)-ProfibusDP		UNIGATE® CX		Note
					UNIGATE® CX: UNIGATE® CX is only available in housing colour Grey.
Protocol	13px		13px (*see note)		UNIGATE® CX-C4Map: UNIGATE® CX-C4Map-PBDPV1 contains the CANopen Mapping. Via the configuration software WINGATE, the CANopen Mapping can be done. UNIGATE® CX-C4Map-PBDPV1 can thus be used like the UNIGATE® CO(M)-ProfibusDP.
Software
Konfigurationssoftware WINGATE	13px		13px		UNIGATE® CX: The configuration file (.gwc) of UNIGATE® CO(M) - ProfibusDP can not* be loaded inUNIGATE® CX-C4Map-PBDPV1.
Mechanics
Housing WxHxD	90 x 127 x 55 mm		46 x 117 x 106 mm
Protection type	IP24		IP20
Connection-Power Supply	Mounting Position
Connection-Power Supply	Frontal-Bottom		Bottom
	screw-plug-connector 2 pol.		screw-plug-connectorr X1 and X2
Power Supply	screw-plug-connector 2 pol.		screw-plug-connector 4 pol. X1	screw-plug-connector 4 pol. X2
+24V/DC (Pwr)	Pin 1		Pin 1		UNIGATE® CX: The power supply is internally bridged between + 24V/DC (Pwr) and + 24V/DC (Out) as well as between 0V (GND) (Pwr) and 0V (GND) (Out). This only has to be done at + 24V/DC (Pwr) and 0V (GND) (Pwr).
0V (GND) (Pwr)	Pin 2		Pin 2
+24V/DC (Out)				Pin 1
0V (GND) (Out)				Pin 2
Housing-Earthing	Earthing Clamp via DIN-Rail		Earthing Clamp via DIN-Rail
	UNIGATE CO(M) - ProfibusDP (Housing-Earthing)		UNIGATE CX (Housing-Earthing)		UNIGATE® CO(M) - ProfibusDP: At elder devices the earthing is done by flat plug connectors or there is no earthing at the device. Example shows UNIGATE CO(M) - ProfibusDP
Anschluss-Seriell	Mounting Position
Anschluss-Seriell	Side Part - right		Top	Bottom
	For 3 pol. screw-plug-connector		screw-plug-connector Service Interfaces	screw-plug-connector X1 und X2
Application Interface (RS232)	screw-plug-connector 3 pol.		screw-plug-connector 3 pol. Service Interfaces
Rx	Pin 1		Pin 1
Tx	Pin 2		Pin 2
AP-GND	Pin 3		Pin 3
Debug-Interface				screw-plug-connector 4 pol. X1 screw-plug-connector 4 pol. X2
Rx-Debug				Pin 3
Tx-Debug				Pin 4
Selection Application Interface	Not selectable		Configurable
RS232	13px		13px (*see note)		UNIGATE® CX: The RS232 interface is used exclusively as a service interface. For example, a 'Reset device' or a 'Firmware Update' (* .hex) can be carried out via this.
Application- Interface Rotary Coding Switches & LEDs	Mounting Position
Application- Interface Rotary Coding Switches & LEDs	Frontal		Frontal
	application interface LEDs		application interface rotary coding switches & LEDs
Rotary Coding Switch S4			13px		UNIGATE® CX: Operating modes may be selected correspondingly as at UNIGATE® CO(M) - ProfibusDP. Attention: Switch position "DD" is reserved for internal use and is not allowed to use.
Rotary Coding Switch S5			13px
LED Power			13px
LED State			13px
LEDs 1/2/4/8 (Error No / Select ID)	13px		13px
Connection Fieldbus	Mounting Position
Connection Fieldbus	Frontal-Top	Frontal-Bottom	Frontal	Top
CANopen		connection via 9 pol. D-Sub connector	connection via 9 pol. D-Sub connector
PROFIBUS	connection via 9 pol. D-Sub socket		connection via 9 pol. D-Sub socket
Termination	Connectible by slide switch		Connectible by slide switch
Fieldbus Rotary Coding Switches & LEDs	Mounting Position
Fieldbus Rotary Coding Switches & LEDs	Frontal-Top	Frontal Bottom	Frontal
CANopen		fieldbus Dip-Switch & LEDs	CANopen Dip-Switch & LEDs
Dip-Switch		13px	13px
LED BUS Power		13px	13px
LED BUS State		13px	13px
PROFIBUS	fieldbus rotary-coding-switches & LEDs		PROFIBUS rotary-coding-switches & LEDs
Rotary Coding Switch High	13px		13px
Rotary Coding Switch LOW	13px		13px
LED BUS Power	13px		13px
LED BUS Error	13px		13px
LED BUS State	13px		13px
Device Description Files
CANopen			13px		UNIGATE® CX: An EDS - file can be generated by configuration software WINGATE.
PROFIBUS DPV0	DAGW2862.gsd		UGIC3218.gsd		UNIGATE® CX: The GSD file for the PROFIBUS can be downloaded from the homepage. GSD-Datei (GSD-File) Icon (DIB-File)
PROFIBUS DPV1			UGIC3218.gsd		UNIGATE® CX: The GSD file for the PROFIBUS can be downloaded from the homepage. GSD-Datei (GSD-File) Icon (DIB-File)
EPLAN
CANopen			13px		UNIGATE® CX: The macro for EPLAN can be downloaded from the homepage. EPLAN - Makro Unigate CL-C4 (Zip-Datei) Compatibility list macros UNIGATE® CL/CX (PDF-File)
PROFIBUS			13px		UNIGATE® CX: The macro for EPLAN can be downloaded from the homepage. EPLAN - Makro Unigate CL-PB (Zip-Datei) Compatibility list macros UNIGATE® CL/CX (PDF-File)